Wraith Electronics box

[gbean]

Given all my electrics will be under the hood, I don't see the need for a slightly thicker box to replace my dinky drop box. But I'll report back once I have both installed.

[The Crawl Space]

Originally Posted by Dostradamas

1 piece drop in box made as heavy & same material as under hood box in black.
Covered area above rear shocks outlined so you could cut it out for droop setup (rear shock mount inverted) or leave covered for stock rear shock mount setup.

Good deal, We'll look at the options available for rear shock mounting and see what will work best for the application

[crazy81]

Got mine today!!!

[The Crawl Space]

Right on, glad you got it a timely manner and thank you for posting up pics

[19_mustang_96]

I want one. Like the the Idea of weather striping on the hood.

[madtinner]

Got mine today. Very nice fit my 2s 5000 venom lipo fit like a glove.
It fits almost perfectly even with the box.

[zero1]

can a 6cell 7.2v nimh fit in it?

[crazy81]

Originally Posted by zero1

can a 6cell 7.2v nimh fit in it?

Yes it can. More than enough room for it.




Sent from my HTC POS tablet using Tapatalk 2

[zero1]

Thanks! How do i go about buying this?
Shipping to singapore?

[crazy81]

Originally Posted by zero1

Thanks! How do i go about buying this?
Shipping to singapore?

Contact The Crawl Space.

As far as shipping, I couldn't begin to tell you...

[gbean]

Got home and checked mine out a bit. I think a little heat gun applied to the front corners of the battery section will help hard case batteries fit down lower a little better .
I'll post pics once I do it.

[bignose13]

got mine..thank you ...now its time to put it in :-)

[Flying Dutchman]

Thanks for the positive feedback guys. TCS should have more boxes in stock after this week as well.

In addition, the rear drop box mold is done. I will knock out a few test parts to verify fit. Once done and approved I figure TCS to have stock of these by the end of next week. Also this drop box will be made of the same material thickness so it should hold up real well.

Thanks again everyone.

[Ricochet]

If the rear box is as good as the front put me down for one.

[Flying Dutchman]

Originally Posted by Ricochet

If the rear box is as good as the front put me down for one.

It will be just as good. Regarding the cover, what would you all like to see? I'm guessing something like a full cover but do you want any kind of features on it or plain?

By Features I mean, fuel tank, toolbox, exc, exc....

I was thinking of incorporating a spare tire mount on one version of the cover for those that have done that coupe mod on the roll cage. Any thoughts?

[Ricochet]

Those ideas all sound good.

[The Crawl Space]

Originally Posted by Flying Dutchman

It will be just as good. Regarding the cover, what would you all like to see? I'm guessing something like a full cover but do you want any kind of features on it or plain?

By Features I mean, fuel tank, toolbox, exc, exc....

I was thinking of incorporating a spare tire mount on one version of the cover for those that have done that coupe mod on the roll cage. Any thoughts?

I like the fuel tank/cell molded into the top rear cover, it will allow for more room and options for running gear placement. People will be able to paint it to get scale points too

I have a couple ideas for the top cover when you have time to swing by the shop

[Dostradamas]

+1 molded in fuel cell in drop box.
Woo Whoooooo! I want one!

[Robchinchilla]

Question. I'm new to this. Will my servo mounted to my axle have room to go into the frame? When its articulating I mean..?

[The Crawl Space]

Originally Posted by Robchinchilla

Question. I'm new to this. Will my servo mounted to my axle have room to go into the frame? When its articulating I mean..?

Welcome to RCC and its toally valid question. Yes, an axle mounted servo will have room to go into the frame thru the suspension cycle.

Da Box is designed for clearance with axle and chassis mounted standard sized servos.