|
| LinkBack | Thread Tools | Display Modes |
12-12-2012, 12:58 PM | #1 |
Rock Stacker Join Date: Dec 2011 Location: Newport, NH
Posts: 55
| Help with Hack on GT3B Trans... Local to NH Please
I just bought a Fly Sky GT3B radio.... I have ordered the Hack kit from Overkill. I can do the physical installs and the soldering of the Plug.. New VR.. Lipo ...Bearing etc... But I'm worried about the programing. The more I read.. the more confused I get. I need help. Is there anybody local to NH or Northern Mass... or VT that has done the hack and can help me with the programming & Teach me how to run it after??? If I can find someone local... I will gladly pay you for your time. Or... is there a HACK FOR DUMMIES thread?? I need step by step... click by click directions... How to install the Programming hack.. them how to set up 4 channels for my Crawler.... Throttle.. Steering... Dig... 4WS.. on my Ax10 Scorpian. Can you help? |
Sponsored Links | |
12-12-2012, 09:10 PM | #2 |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Re: Help with Hack on GT3B Trans... Local to NH Please
You should of got an email with your order that had alot of good resources in it to read...
|
12-13-2012, 02:33 AM | #3 | |
Rock Stacker Join Date: Dec 2011 Location: Newport, NH
Posts: 55
| Re: Help with Hack on GT3B Trans... Local to NH Please Quote:
Yes... I did. But as I already said. The more I read.. the more confused I become. I am new to the RC world... and not good with computers. I'm hoping once I get the parts installed and plug it in... it will make more sense... But right now I'm pretty much lost. | |
12-13-2012, 11:00 AM | #4 |
Quarry Creeper Join Date: Jan 2010 Location: Lunenburg
Posts: 349
| Re: Help with Hack on GT3B Trans... Local to NH Please
I was surprised how easy the hack was. Follow the directions and you'll be OK. I'm in MA if you get really stuck. Only did one radio so far but everything went very smooth.
|
12-13-2012, 01:57 PM | #5 |
RCC Addict Join Date: Feb 2010 Location: New Jersey shore
Posts: 1,482
| Re: Help with Hack on GT3B Trans... Local to NH Please
looking at the manual is confusing me a bit too. no very little about this stuff. the 3rd channal on my remote is not working
|
12-13-2012, 02:36 PM | #6 |
Rock Stacker Join Date: Dec 2011 Location: Newport, NH
Posts: 55
| Re: Help with Hack on GT3B Trans... Local to NH Please
went to use my gt3b today for the first time and the reverse was not working very well.. try rebinding or calibrating to esc and now its not working at all. esc does not et a reverse signal... so it wont calibrate. very frustrating |
Help with Hack on GT3B Trans... Local to NH Please - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
GT3B Hack Question and Answer Thread | losikid | Electronics | 4922 | 09-23-2023 07:34 AM |
fs gt3b setup after hack. | foratm | Electronics | 32 | 06-27-2020 12:03 PM |
gt3b hack programming | WICKEDWOLFRC | Electronics | 2 | 11-05-2011 12:25 AM |
Losikid gt3b hack review. | WICKEDWOLFRC | Electronics | 0 | 10-16-2011 06:11 PM |
GT3B Firmware Hack Kits | losikid | Vendors Electronics | 0 | 07-29-2011 04:24 PM |
| |