|
| LinkBack | Thread Tools | Display Modes |
05-11-2013, 09:27 AM | #1 |
Newbie Join Date: Apr 2013 Location: Utah county
Posts: 14
| Maddd cutting out, New remote???
Hey ya'll, So I have almost upgraded everything on my ridgecrest. Motor, Esc, and servo. Im thinking something is too powerful for the next? I got a Savox 500oz servo (that wines all the time) and just installed the Tekin fx esc bc the stock esc burned up... But when the car gets about 5 feet away i lose all function.. Do I need to upgrade my remote and reciever now? If so what do you guys suggest? |
Sponsored Links | |
05-11-2013, 09:30 AM | #2 |
Rock Crawler Join Date: Mar 2006 Location: Up North
Posts: 617
|
Looks like you need to install a BEC.....the servo you are running is using too much power....the esc is shutting down. Google Castle BEC(Battery Eliminator Circuit) |
05-11-2013, 09:33 AM | #3 |
Newbie Join Date: Apr 2013 Location: Utah county
Posts: 14
| Re: Maddd cutting out, New remote???
I put the CC BEC on with my stock axial ESC and the esc literally went up in smoke? When i hold the car i can have it punched on full throttle and turn the wheels with no problem its when the car gets like 5 feet away
|
05-11-2013, 09:34 AM | #4 |
Rock Crawler Join Date: Mar 2006 Location: Up North
Posts: 617
|
I would try changing the batteries then on you TX....see if that helps.
|
05-11-2013, 09:36 AM | #5 |
Rock Crawler Join Date: Mar 2006 Location: Up North
Posts: 617
|
I still think that your ESC is shutting down to overload from that servo 500 oz is alot of juice ;)
|
05-11-2013, 09:37 AM | #6 |
Newbie Join Date: Apr 2013 Location: Utah county
Posts: 14
| Re: Maddd cutting out, New remote???
Yea I thought so too... Should I downgrade a little? What is a good oz for a servo I crawl on rocks mostly
|
05-11-2013, 09:38 AM | #7 |
Rock Crawler Join Date: Mar 2006 Location: Up North
Posts: 617
|
No need to downgrade.....just install a bec..and you should be good to go.
|
05-11-2013, 09:40 AM | #8 |
Rock Crawler Join Date: Mar 2006 Location: Up North
Posts: 617
|
The whining is because its a digital servo that tries to center itself....completely normal....
|
05-11-2013, 10:09 AM | #9 |
Newbie Join Date: Apr 2013 Location: Utah county
Posts: 14
| Re: Maddd cutting out, New remote???
Right on thanks man i appreciate it!!!
|
05-11-2013, 10:27 AM | #10 |
Rock Crawler Join Date: May 2012 Location: Upland
Posts: 901
| Re: Maddd cutting out, New remote???
do you have a BEC or not? I cannot tell
|
05-11-2013, 12:53 PM | #11 |
I wanna be Dave Join Date: Nov 2010 Location: 07456 N. NJ USofA
Posts: 8,314
| Re: Maddd cutting out, New remote??? Ummmm...post 3 states he had an external BEC. Not sure if he still has it. Pimp.....when you had the CC external BEC, was it direct to the servo or the RX? If to the RX, did you pull the red wire from the ESC to RX? If not, the ESC BEC likely died since it fought the external BEC and lost. The rule is.......only a SINGLE BEC to the RX, NEVER 2 BEC's to the RX. Thus, if you're running a dual ESC rig, only one has the red ESC to RX wire connected, the other is removed and taped off. Same for an external BEC, if run through the RX, remove (and tape off) the ESC to RX connection. |
Maddd cutting out, New remote??? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
new r/c remote | crwler | Electronics | 0 | 03-08-2013 07:23 PM |
remote | wiseman | Newbie General | 8 | 03-08-2012 11:52 AM |
Cutting a Cutting Board | BJoe | Tools, and Procedures | 37 | 12-22-2009 12:34 AM |
remote | major94 | Tamiya Clod Buster | 8 | 11-22-2006 03:40 PM |
cutting tranny when cutting bottom of chassis off... | dieselfuel | Newbie General | 1 | 02-23-2006 08:10 PM |
| |