|
| LinkBack | Thread Tools | Display Modes |
02-23-2016, 09:42 AM | #1 |
Quarry Creeper Join Date: Aug 2008 Location: Sweden
Posts: 214
| MMP + Pro Puller 540XL Shutter help? https://www.youtube.com/watch?v=ySo65L1_K0Q This happens with low throttle before taking off! Pro Puller 540XL with MMP with smartsense on and lastest firmware, new sensor wire. If i disconnect the sensor wire the shutter/hesitation stops, is the sensorboard broken maybe? Last edited by Haziza; 04-03-2016 at 06:15 AM. |
Sponsored Links | |
02-23-2016, 09:47 AM | #2 |
Scale Detail Engineering Join Date: Apr 2010 Location: Turtle Island
Posts: 5,573
| Re: MMP + Pro Puller 540XL Shutter help?
The shutter stops all together when the sensor wire is removed? Because, in the video it looks like the sensor wire is bad or not plugged in. |
02-23-2016, 09:49 AM | #3 |
Quarry Creeper Join Date: Aug 2008 Location: Sweden
Posts: 214
| Re: MMP + Pro Puller 540XL Shutter help?
Yes video is with wire connected, i did try with a new sensor wire but it did not help! With the sensor wire off its less shutter but not so smooth. Last edited by Haziza; 02-23-2016 at 10:20 AM. |
02-23-2016, 12:30 PM | #4 |
Quarry Creeper Join Date: Aug 2008 Location: Sweden
Posts: 214
| Re: MMP + Pro Puller 540XL Shutter help? |
03-23-2016, 09:38 PM | #5 |
Newbie Join Date: Jun 2013 Location: niagara falls
Posts: 24
| Re: MMP + Pro Puller 540XL Shutter help?
solved my issue by updating software on mmp
|
03-23-2016, 09:39 PM | #6 |
Newbie Join Date: Jun 2013 Location: niagara falls
Posts: 24
| Re: MMP + Pro Puller 540XL Shutter help?
i turned of smart sense and run sensored only
|
03-25-2016, 02:04 PM | #7 |
Quarry Creeper Join Date: Feb 2011 Location: Nevada
Posts: 302
| Re: MMP + Pro Puller 540XL Shutter help?
I have the Mamba Monster X and the 540 XL. I run mine with Smart Sense on. I understand that the way Holmes engineered the XL, it won't be as smooth as the other Puller motors or a Tekin Pro4 but gives that up in torque. In the first video you posted, the thing that I wondered is how is your gear mesh? Is it too tight? |
03-25-2016, 02:08 PM | #8 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Re: MMP + Pro Puller 540XL Shutter help?
It sounds like there is voltage trying to start the motor, but the load is very high and it jumps to life. So the throttle response is there (I can hear a big range when you are pulling more trigger before startup), but something is sticking.
|
03-29-2016, 05:37 AM | #9 |
Quarry Creeper Join Date: Aug 2008 Location: Sweden
Posts: 214
| Re: MMP + Pro Puller 540XL Shutter help?
I did totally miss this answer, could it be a bad reciver? I use a old Airtronics MX3 for it arm. Strange thing is when I realese the throttle back its very smooth but the start up is a bit laggy as seen in the videos! I have tryed different gear mesh as well not difference! Anything ode what I should do next? |
03-29-2016, 05:50 AM | #10 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Re: MMP + Pro Puller 540XL Shutter help?
The xl isn't the smoothest starting motor. Once spinning you can reduce speed.
|
03-30-2016, 10:21 AM | #11 |
Newbie Join Date: Aug 2008 Location: Not the city
Posts: 26
| Re: MMP + Pro Puller 540XL Shutter help?
I had a similar problem with mine but only in forward or reverse depending on the wiring from the MMP to the motor. The problem ended up being a setting on the radio. Not sure how it got turned on but ABS was turned on. After turning it off, no problems.
|
04-02-2016, 09:46 AM | #12 |
Quarry Creeper Join Date: Aug 2008 Location: Sweden
Posts: 214
| Re: MMP + Pro Puller 540XL Shutter help?
I understand it's not so smooth. But why dose the motor hesitates so much before it starts to spin? Checked other videos on YouTube and I can't hear it. If I order a new sensor board would it solve it? Opened the motor to look and the sensors were covered with think layer of waterproofing could that be the problem maybe? I have never used the truck in water anyway so the waterproofing dose not matter to me. Got it with waterproofing from HH MMP + Pro Puller 540XL. Last edited by Haziza; 04-02-2016 at 10:23 AM. |
MMP + Pro Puller 540XL Shutter help? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
The Holmes Puller Pro BL 540XL 3500kv the YETI Grail? | npcaldwell | Axial Yeti | 164 | 03-28-2017 07:32 PM |
Holmes pro puller 540XL - Fitment help! | Haziza | Axial Yeti | 3 | 05-04-2015 06:42 PM |
puller pro 540xl vs trailmaster bl sport 540 | bombagee | Electronics | 6 | 05-02-2015 01:08 PM |
| |