|
| LinkBack | Thread Tools | Display Modes |
03-18-2019, 04:03 PM | #1 |
Quarry Creeper Join Date: Nov 2018 Location: Oakley
Posts: 479
| Setting up GT3C channel 3 for Monster X aux wire?
I am having a little trouble figuring this out. I have the GT3C setup to be 3 channel, and I have my Mamba Monster X Aux wire in Ch 3 on the FS-R9B. I assume I am screwing up the settings in the Tx itself, can anyone give me some guidance on how channel 3 needs to be setup to trigger the Aux wire for Rock Race/Crawler mode on the ESC? EDIT: So it actually is kinda working, however it is being triggered based on the Ch 3 trim switch. At -100 tirm its in Rock Race mode(no drag brake) at 0 trim it got some drag brake, and at +100 trim its full on lock up the tires drag brake. Is there a way to get it to just be triggered off the CH 3 button? Just on/off? The button currently doesn't do anything. Last edited by mass-hole; 03-18-2019 at 04:13 PM. |
Sponsored Links | |
03-18-2019, 04:09 PM | #2 |
Rock Crawler Join Date: Jun 2018 Location: Orange County, CA
Posts: 711
| Re: Setting up GT3C channel 3 for Monster X aux wire?
I can! First you need castle link to ENABLE the 3rd wire. Bastards make it impossible to turn on manually. Then once enabled in castle link, you are able to choose what that AUX does. I use it on a mini for brake on or off. |
03-18-2019, 04:15 PM | #3 |
Quarry Creeper Join Date: Nov 2018 Location: Oakley
Posts: 479
| Re: Setting up GT3C channel 3 for Monster X aux wire? Hey, thanks for the response. When you answered I was editing my post. The Aux wire is functioning, my issue is on the TX side. I dont have the settings correct to use the CH3 switch for on/off.
|
03-18-2019, 04:44 PM | #4 | |
Rock Crawler Join Date: Jun 2018 Location: Orange County, CA
Posts: 711
| Re: Setting up GT3C channel 3 for Monster X aux wire? Quote:
I have my endpoints at stock settings on channel 3 and it works as a on or off for ROCK RACER /crawler mode as is? Perhaps your endpoints are all messed up? Try stock settings. I have not tried the brake LEVEL adjustment setting. I am on rock racer (no drag) / crawler mode (instant drag brake) via that 3rd button and it goes from one to the other just fine. Last edited by BIGW0RM; 03-18-2019 at 04:49 PM. | |
03-18-2019, 08:49 PM | #5 |
Quarry Creeper Join Date: Nov 2018 Location: Oakley
Posts: 479
| Re: Setting up GT3C channel 3 for Monster X aux wire?
I actually figured out that the Ch 3 Trim switch is great for the AUX wire control. The wire takes the frequency from the receiver and can modulate the amount of drag brake on the fly while also allowing you to have rock race or crawl mode active(changes the reverse mode from "with reverse" to "crawl reverse"). You can set the increments for the trim control to allow finer tuning of the drag break on the fly. I currently have it set to +/- 40% so I can go from 0% drag brake to 100% drag brake in 5 increments. It's pretty clever.
|
03-18-2019, 09:02 PM | #6 | |
Rock Crawler Join Date: Jun 2018 Location: Orange County, CA
Posts: 711
| Re: Setting up GT3C channel 3 for Monster X aux wire? Quote:
| |
03-19-2019, 08:31 AM | #7 |
Quarry Creeper Join Date: Nov 2018 Location: Oakley
Posts: 479
| Re: Setting up GT3C channel 3 for Monster X aux wire? |
Setting up GT3C channel 3 for Monster X aux wire? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
CC Mamba X (white) aux wire | Fishcharger | Electronics | 25 | 03-24-2019 07:35 PM |
Mamba X aux wire glitch, can't get it to work properly | Antsiranean | Electronics | 6 | 02-17-2019 03:50 AM |
on/off switch via Aux channel for lights | Angus_Beef | Electronics | 17 | 04-06-2015 08:43 PM |
Spektrum dx3r aux channel,help!!!! | lgnitro | Electronics | 4 | 06-07-2009 12:31 AM |
Dx6i AUX 1 channel setup | Brasher | Electronics | 7 | 05-22-2009 08:07 PM |
| |