![]() | #81 |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]() |
![]() | ![]() |
Sponsored Links | |
![]() | #82 |
I wanna be Dave Join Date: Jan 2006 Location: Iowa, the antirecreation state!
Posts: 2,227
| ![]()
LOVE the servo mount. Just keeps getting better
|
![]() | ![]() |
![]() | #83 |
SuperShafty.com Join Date: Jan 2008 Location: Visalia CA
Posts: 2,902
| ![]()
yeah man this is lookin really good.
|
![]() | ![]() |
![]() | #84 |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]() |
![]() | ![]() |
![]() | #85 |
I wanna be Dave Join Date: Jan 2006 Location: Iowa, the antirecreation state!
Posts: 2,227
| ![]()
Sheesh, If I didn't no any better I'd say this was a MOA rig. Looks killer!!
Last edited by Bart bender; 05-17-2014 at 10:34 PM. |
![]() | ![]() |
![]() | #86 |
Rock Crawler ![]() Join Date: Oct 2011 Location: south of nowhere
Posts: 788
| ![]()
So bad ass, how does it crawl??? ![]() |
![]() | ![]() |
![]() | #87 |
Rock Crawler ![]() Join Date: May 2012 Location: Washougal
Posts: 625
| ![]()
Very cool as usual Joey! Has to be one of the beefiest sporties every ![]() |
![]() | ![]() |
![]() | #88 | |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]() Thanks mj Quote:
![]() Thanks. It did good the couple times i got to drive it. Definitaly needs same tuneing before its comp ready though. Thanks sam | |
![]() | ![]() |
![]() | #89 |
I wanna be Dave Join Date: May 2007 Location: Fairfield ME
Posts: 3,885
| ![]()
So what does it weigh rtr?
|
![]() | ![]() |
![]() | #90 |
Rock Crawler Join Date: Sep 2010 Location: Keego Harbor, MI.
Posts: 951
| ![]()
I'm soooooo Jelly ![]() Just amazing bro Regards, Rick |
![]() | ![]() |
![]() | #91 |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]() |
![]() | ![]() |
![]() | #92 |
Rock Crawler ![]() Join Date: Oct 2011 Location: south of nowhere
Posts: 788
| ![]() ![]() How many shims did you use on the ring gear side of the locker? I can't seem to get that pinion to mesh at all.??? |
![]() | ![]() |
![]() | #93 | |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]() Quote:
quite a few. only about half the bearing ends up in the pocket. you have to run a thinner bearing on the other end. here is the bearing that ended up working for me. i didnt but thinking about it, its probably a good idea to find a wider bearing so you dont have to run so many shims and you get more bearing back in the pocket. ![]() ![]() | |
![]() | ![]() |
![]() | #94 |
I wanna be Dave Join Date: Jan 2006 Location: Iowa, the antirecreation state!
Posts: 2,227
| ![]()
Is that a Mugen gear set you're using? Went back and read but either missed it or it wasn't mentioned.
|
![]() | ![]() |
![]() | #95 |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]() |
![]() | ![]() |
![]() | #96 |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]() |
![]() | ![]() |
![]() | #97 |
Rock Stacker Join Date: May 2008 Location: Des Moines
Posts: 81
| ![]()
Hey Joey, thanks for posting this all , I've really enjoyed reading it. nicely done!
|
![]() | ![]() |
![]() | #98 |
SuperShafty.com Join Date: Jan 2008 Location: Visalia CA
Posts: 2,902
| ![]()
how are you attaching those knuckle weights? looks great btw |
![]() | ![]() |
![]() | #99 |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]() |
![]() | ![]() |
![]() | #100 |
RCC Addict Join Date: Nov 2006 Location: burlington
Posts: 1,042
| ![]()
Its been a little quiet in here. So i figure i will show some small changes i have done. Didnt like how the toy was performing with the rear links and shocks sharing the same mounting hole. So i went back to how i first had it, but i did move them up and forward on the chassis to still try to get it a little lower in the rear. Also changed out the rear upper links to Ti. took out the axial plastic drivelines an swaped them for S.D.I propeller shafts. ![]() |
![]() | ![]() |
![]() |
Tags |
#ayalametalworks, #crawlerinnovations |
![]() | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Difference between X-factor, Twin Force and Mad Force axles | Flatty | XTM Crawler | 1 | 09-11-2008 06:48 PM |
Is the Mad Force interchangable with Twin Force part | Trac95ker | Kyosho Crawlers | 2 | 04-12-2005 01:11 AM |
Thread Tools | |
Display Modes | |
| |