KCRC - Kansas City Remote Crawlers -

[viper6171]

Originally Posted by the DMG

yep,
its going to goooooo all right,
right into the middle of September

uuuugggghhhhhh you had to say that didn't you

[ohh EPiC FAiL]

anyone got a set of axial AX10 c-hubs? i need the non 8* version for my bully.

[ev0l]

Originally Posted by ohh EPiC FAiL

anyone got a set of axial AX10 c-hubs? i need the non 8* version for my bully.

scrtatch that, XR10 chubs. my bad.

[ohh EPiC FAiL]

Originally Posted by ev0l

scrtatch that, XR10 chubs. my bad.

it's cool, never mind anyway i impulse-ordered some today along with some 18g wire

i'm starting the process of putting my bully on a diet. i ordered the DLux delrin tubes with longer fronts to make it the same width as a berg, and if i remember correctly the delrin tubes are about 5oz per axle lighter than the cast tubes

[ev0l]

My dog did about 30 laps around my track today chasing the EXO. She started turning some pretty good laptimes. I had to disqualify her in the end though because she started cutting corners.

[RivBlueNoma]

Dang dogs cheat every time they think you arent looking.

Originally Posted by ev0l

My dog did about 30 laps around my track today chasing the EXO. She started turning some pretty good laptimes. I had to disqualify her in the end though because she started cutting corners.

[BC Racing]

Anyone in the market for a FF4 chassis, VP dig, VP zero-ack knuckles and d-lux knuckle weights?



Getting ready to go up in the FS section.

[ev0l]

Building a new rig??

Originally Posted by BC Racing

Anyone in the market for a FF4 chassis, VP dig, VP zero-ack knuckles and d-lux knuckle weights?



Getting ready to go up in the FS section.

[RivBlueNoma]

I know Jerry was looking for another FF4 chassis.

Originally Posted by BC Racing

Anyone in the market for a FF4 chassis, VP dig, VP zero-ack knuckles and d-lux knuckle weights?



Getting ready to go up in the FS section.

[the DMG]

Originally Posted by RivBlueNoma

I know Jerry was looking for another FF4 chassis.

found one all ready !!
thx for think abought me though

[RivBlueNoma]

Look at all that fancy color coordination.

Originally Posted by the DMG

found one all ready !!
thx for think abought me though

[ohh EPiC FAiL]

okay so i've got the delrin tubes coming from DLUX for my bully, and they are i believe 1/2" wider for the front. does anyone have the ability to weld me some shafts for it? i'm thinking i want to use XR10 or wraith universals cut off and welded to the cut off XVD to get the extra length needed and the extra steering would be nice as well. if you can do it let me know

[RivBlueNoma]

Highland crawler started off doing this same mod to XR shafts to use them on his berg but they kept snapping at the weld joints. That's how he eventually got to the point of making his Berg/XR Hybrid shafts that no one can get.

[ohh EPiC FAiL]

Originally Posted by RivBlueNoma

Highland crawler started off doing this same mod to XR shafts to use them on his berg but they kept snapping at the weld joints. That's how he eventually got to the point of making his Berg/XR Hybrid shafts that no one can get.

Oh okay nevermind then. I guess I'll just have to wait til the super bully XVDs come back in stock.


Sent from my iPhone 4S using Tapatalk

[Harley]

Originally Posted by ohh EPiC FAiL

Oh okay nevermind then. I guess I'll just have to wait til the super bully XVDs come back in stock.


Sent from my iPhone 4S using Tapatalk

Could cut down two long side Wraith shafts. The new VP chromo shafts will probably be about $50 per side.

[ohh EPiC FAiL]

Originally Posted by Harley

Could cut down two long side Wraith shafts. The new VP chromo shafts will probably be about $50 per side.

The problem is that the axial universals aren't thick enough to fit into the bully locker. I'm wanting to say the bully shafts are 6 or 8mm and the axial universals are 4mm


Sent from my iPhone 4S using Tapatalk

[fordwheeler]

Anyone interested in a scx10 roller, started out as rtr honcho currently setup with a dinky summit cradle, brand new (never ran) summit trans, new mip center shafts, vp 8° chubs/knuckles, f/r 4-link, losi 4" crawler shocks, 1.9 flat irons on proline titus rims and several other parts/ pieces to sweeten the deal

Also up for grabs is my mrc pro rtr! And mrc gc3 roller. I've got lots of mrc parts, enough to have 2 running mrc's plus extra parts ...tires/rim combos, electronics, axlecases, shafts etc. If anyone wants to buy me out of 1.9 comp equipment I'll throw in a basket case associated rc18t with several hop up parts.

also got:
Servos
Esc's
batteries
Bodies

99% of what I have was bought brand new by me, this stuff needs to go and would like to see a local benefit from this.

Let me know if interested and I'll post up a more specific detailed list
Thank you KCRC! its been REAL FUN!

[BC Racing]

Jerry....Have you had a guy talking to you about building a blue torch replica?
He joined rcc - screename is "harrison", believe you guys have emailed back and forth couple times. He is my cousin Brent...and was just worried you thought he was full of shit or a kid. He is dead serious...its actually the one I have always wanted to build. Need to get him hooked up with Neal as well...to try and replicate the skins.

[ev0l]

Has the club ever put on a demo at a car show or anything?

[the DMG]

Originally Posted by ev0l

Has the club ever put on a demo at a car show or anything?

not @ a car show,
we did a demo comp in front of Hobby Town in Lees summit once.
turn out was not to bad for a rainy day

that's what i am hoping to use some of these obstacles i am trying to build for - demo

moving the real rock in a pain