08-20-2015, 09:44 PM | #81 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6
Finally got some pics of the wiring. Now keep in mind everything is not installed in there at the moment. I sold my BRXL and am currently going to run a Tekin FXR (from my Green LJ now that it's for sale). The wiring is in a bit of a shambles. So sue me! Here you can see the chassis area under the cab. I reamed a hole under the rearmost part of the cab's interior and all of the wires are routed through it. I also needed extensions for my servo leads. The Deans plug for the motor is inside the cab. Also, note the leads for the motor are on the bottom. The reason is if you solder them on top, they'll hit the body when it's lowered. I still need to secure the wiring. I think I'll use some "P" clips hot glued to the underside of the body. And the rat's nest inside the cab. Call it the "sleeper" portion of the cab, if you will. Here's where the more sensitive electronics reside. The Tekin FXR, Castle BEC for the steering servo, 5000mah 3s battery (not shown), the receiver, etc. Eventually I hope to have a sound module in there, but that may go on the bed....hidden out of sight, of course! If you look in the top left corner you can see the hole I made for the wires. I also did some more work on the truck this evening. I cleaned up all of the holes (and drilled new ones as needed) in order to accommodate the new, shorter wheelbase. I also hacked the bed's subframe for the upcoming shortening of the chassis. I'm going to shorten it for a near 90 degree departure angle. And how the wheelbase looks now. I'll be able to eliminate several inches of length from the frame rails, too. Definitely looking much more like a trials truck than a Russian logging vehicle now. |
Sponsored Links | |
08-21-2015, 07:50 AM | #82 |
~THE SCALE SHOP~ Join Date: Apr 2006 Location: KILLEEN TX
Posts: 10,056
| Re: Tommy's Beast II 6x6
russian logging vehicles FTW!
|
08-30-2015, 06:46 PM | #83 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6
The truck has always had a pretty significant rake and really stiff springs. This all got even worse when I removed the cargo bed. So tonight I did a few things. First off, I swapped around a bunch of springs that I had bought for my Losi MRC back in 2009. It's now much softer all around and has usable up and down travel from the normal ride height. But I noticed the front shock towers were higher than the rears. This resulted in a lower front ride height. So I popped a few new holes in the shock towers to address this. Yes, it raised the ride height by doing this, but I then softened the springs so it came back down some. Then I softened the rear springs a LOT so it now sits nice and level even with a cab full of electronics and battery. I also swapped out the tires. I LOVED the look of the MIL-SPECs, but wanted the performance and looks that the Flashpoints offer. Much better for a trials truck! It even has some articulation now! |
08-30-2015, 09:19 PM | #84 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6
I should also point out that with the amount of weight on the front wheels, the stock foams all but collapsed. So I installed some 4.25" tall Crawler Innovations Lil' Nova two stage foams with a firm outer. Much better and I can't wait to see how it crawls. The rears are currently running stock foams since there's so little weight back there.
|
08-30-2015, 09:26 PM | #85 |
I wanna be Dave Join Date: Aug 2005 Location: NE Ohio
Posts: 8,817
| Re: Tommy's Beast II 6x6
Man these are so cool
|
08-31-2015, 10:34 AM | #86 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6 |
09-07-2015, 08:35 PM | #87 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6
Far from "finished", but I finally got a chance to take it offroad today. It was not without problems, but overall it performed pretty well. As expected, the front overhang is a killer. In the ragged rocks and steep approaches, it was a.....challenging.....truck to drive to say the least. But it climbs like a mountain goat! Very impressive! Unfortunately, the middle axle has a lot of twist under load. The rear driveshaft came out a couple times. But the main problem was the front aluminum link mount that sheared!! Here's some pics... CI foams doing their job very well! This was a very off camber spot. A familiar site today. Need to see if I can make a metal one with more spline engagement. |
09-07-2015, 09:11 PM | #88 |
Rock Crawler Join Date: Apr 2014 Location: Portland
Posts: 835
| Re: Tommy's Beast II 6x6
Beast is looking Beastly.. Weathering looks great with out over doing it.. Sorry about the breakage. |
10-17-2015, 12:52 PM | #89 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6
Been a while, but we may be doing some crawling tomorrow and I wanted to get the 6x6 up and going again. First off, I ordered a "Hercules" metal rear driveshaft from AsiaTees.com. It looks cool, but is awfully small. I'm concerned about how strong it will be when subjected to the weight of this rig. The quality was also sketchy. You see, here's the "meat and potatoes" of the driveshaft. All metal. Looks decent enough. But they have these black couplers that are solely for aesthetics. Well, they're aluminum and threaded. So the pins to attach to the axles don't slide through. I had to drill them out and now they work fine. A silly oversight by the manufacturer. And installed... I also replaced the lower link/track bar mount. Here's the damage from last time: I should also point out that last time out I bent the drag link! I guess pushing 500 ounces of torque through it was enough to "boomerang" it! I just bent it back into shape, but am pretty sure it'll just happen again! No pics 'cause there really wasn't much to show. |
10-18-2015, 05:18 PM | #90 |
~THE SCALE SHOP~ Join Date: Apr 2006 Location: KILLEEN TX
Posts: 10,056
| Re: Tommy's Beast II 6x6
regarding the front overhang, what about moving the bumper up to the bottom of the grill, and removing the side steps?
|
10-18-2015, 08:48 PM | #91 | |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6 Quote:
It is. It needs to be since I shortened the distance between the rear 2 axles. | |
10-28-2015, 05:57 PM | #92 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6
I haven't beaten on the truck too badly, but the rear driveshaft is holding up so far...and hasn't popped off, either. So far, so good. Now that it's running again I've decided to proceed with the build. Time to do something about the lack of a proper bed on this thing. I haven't yet decided exactly how I want the bed to look, but know I'll need to start with a flat bed. First was to get some styrene and bond it to the substructure of the bed. Next was to test fit it on the truck and put my drifter chassis on it. No, it won't haul the drifter. I was just playin'. I wanted some texture on the bed so I got some diamond plate for it. Liking it so far. Still needs some more details and eventually I'll build a cage for the bed and an exo-cage for the cab. |
10-31-2015, 12:03 AM | #93 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6
A little more bed detail... |
10-31-2015, 08:30 AM | #94 |
~THE SCALE SHOP~ Join Date: Apr 2006 Location: KILLEEN TX
Posts: 10,056
| Re: Tommy's Beast II 6x6
interesting slope. whats the idea? |
10-31-2015, 09:49 AM | #95 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6 Well, basically I'm just trying to make it look more like a European trials truck and it seems like there are a variety of beds on them. Some are just empty flatbeds, but that's a bit boring. Some have exo-cages, as well as roll cages attached to the bed...both of which I plan on adding. Some have a standard cargo bed, but that's not the look I'm after, either. Some have sponsors and it seems they add small "billboards" to them for their sponsors' logos. That's kind of what I'm going for. Here's a couple examples of what I mean...well, except for the redneck sitting in the bed! |
10-31-2015, 12:04 PM | #96 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6
Every big diesel needs a stack, right? |
11-17-2015, 04:24 PM | #97 |
Quarry Creeper Join Date: Jun 2013 Location: Escondido, San Diego, CA
Posts: 261
| Re: Tommy's Beast II 6x6
What shifters did you use inside the cab what kits were they from?
|
11-17-2015, 04:28 PM | #98 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6 |
11-17-2015, 04:34 PM | #99 |
I wanna be Dave Join Date: Feb 2009 Location: Cowtown, USA
Posts: 2,780
| Re: Tommy's Beast II 6x6
Looking good. Hmm....I have yet to see a video of this beast hauling anything. #6pack? |
11-18-2015, 08:16 AM | #100 |
I wanna be Dave Join Date: Aug 2008 Location: Austin, TX, USA
Posts: 4,273
| Re: Tommy's Beast II 6x6 |
Tommy's Beast II 6x6 - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
RC4WD Beast II 6x6 | IronGut | Multi Axle Rigs | 7 | 04-22-2015 09:30 AM |
The Beast 6x6 revised | blumaro | Multi Axle Rigs | 9 | 03-14-2014 02:11 PM |
| |