| |
03-21-2015, 05:51 AM
| #1 |
| Pebble Pounder Join Date: Feb 2014 Location: Okinawa, Japan
Posts: 151
|  My Unimog is Finished!      Holmes Hobbies Torquemaster Sport 55t Motor Robinson Racing Hardened 16T Pinion Gear Axial AE-2 ESC with drag brake and low voltage cutoff and deans connector Toward Pro MG946R (Have had great luck with these servos) Aluminum Servo Arm and aftermarket steering linkage Fast Eddy Bearings Vaterra TSL Super Swampers Weights in each wheel Brick cutoff and skid plate installed Locked front and rear differentials Yeah Racing CVDs Yeah Racing Aluminum Knuckles Yeah Racing Aluminum C-Hubs Tamiya Aluminum Hexes Has mounts for headlights/taillights but not installed Body painted with Tamiya paint, light sand and black, no cracks Team Associated body pins I just wanted to share my finished build before I sell it. It's going on Ebay tomorrow! I enjoy building them far more than I do running them. |
|  |
| Sponsored Links | |
| | |
|
03-21-2015, 08:42 AM
| #2 |
| Newbie  Join Date: Jan 2013 Location: Denver
Posts: 15
| Re: My Unimog is Finished!  Congrats Great Job.... I cant ever finish 1 complete kits with out changing it around 4 or 5 times... each time costing 100s more ... lol.. You should be a Proud POPA....  |
|
| |
|
03-21-2015, 06:06 PM
| #3 |
| Rock Crawler Join Date: Dec 2014 Location: In the sticks
Posts: 913
| Re: My Unimog is Finished!  |
|
| |
|
03-21-2015, 07:17 PM
| #4 |
| Newbie Join Date: Apr 2010 Location: Homestead,Fl
Posts: 31
| Re: My Unimog is Finished!
Clean build!!!! |
|
| |
|
03-21-2015, 08:12 PM
| #5 | |
| Newbie Join Date: Sep 2014 Location: London
Posts: 21
| Re: My Unimog is Finished! Quote:
| |
|
| |
|
03-21-2015, 09:28 PM
| #6 |
| Pebble Pounder Join Date: Jun 2009 Location: Canada
Posts: 196
| Re: My Unimog is Finished!
Looking good bro!
|
|
| |
|
03-22-2015, 02:23 AM
| #7 |
| Pebble Pounder Join Date: Feb 2014 Location: Okinawa, Japan
Posts: 151
| Re: My Unimog is Finished!
Hey thanks guys. This was my second cc01 that I've built so I knew what mods it needed and what mods it didn't. I also did very well on cost too because I parted out the stock motor esc an light kit and got the kit on sale.
|
|
| |
|
03-22-2015, 02:28 AM
| #8 |
| Pebble Pounder Join Date: Feb 2014 Location: Okinawa, Japan
Posts: 151
| Re: My Unimog is Finished!
Looking to build yeti xl or a savage nitro kit. Unfortunately I think the savage kit may be discontinued. They are out of stock everywhere and the motor that comes in the kit shows discontinued
|
|
| |
|
03-22-2015, 06:32 PM
| #9 |
| Quarry Creeper Join Date: Oct 2014 Location: Milpitas
Posts: 258
| Re: My Unimog is Finished!
Nice. So sounds like you have done this before... do you typically make any profit or at least break even? (not counting labor of course) I'm sure it's easier when it's mint and not used at all. I got a boat form a guy named vett over at rcg and he pumped them out by the dozen- then would promptly sell- he did not run them only liked to build. |
|
| |
|
03-23-2015, 01:05 AM
| #10 | |
| Pebble Pounder Join Date: Feb 2014 Location: Okinawa, Japan
Posts: 151
| Re: My Unimog is Finished! Quote:
| |
|
| |
|
03-24-2015, 01:52 PM
| #11 |
| Newbie Join Date: Sep 2008 Location: St. Louis
Posts: 40
| Re: My Unimog is Finished!
I like it all! I wish Yeah made their c-hubs in black because I don't want to stick those blues on my Unimog. |
|
| |
 |
My Unimog is Finished! - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| CR-01 Unimog from Portugal... finished setup and firts hop-ups | PMateus | Tamiya CR-01 | 6 | 09-14-2009 08:12 AM |
| Unimog Finished | confusednub | Tamiya CR-01 | 11 | 10-08-2008 08:31 PM |
| TLT finished! Half aluminum tube High gc Low cg FINISHED | RCMFMaxxMan | Tamiya TLT Crawlers | 12 | 08-08-2005 12:18 AM |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
