10-02-2016, 08:00 PM | #1 |
Pebble Pounder Join Date: Mar 2016 Location: Harrisburg/York
Posts: 128
| Our LNC 2.0 and LCC...
I figured I'd post up a few pics... I was into RC's back in the early 2000's, when Nitro and the Team Associated TC3 / NTC3 were the touring cars to have. Got the bug again when we went to a local event, got the 3 year old a ECX Temper 1/18 and me a LNC 2.0... Well once he mastered the ECX and I ran across and LCC roller, it was time for him to get a 1/10th. Here is our toys; LNC 2.0 4WS using the Losi LOSB2046 Kit Spektrum S605 for both F/R Steering Servo's Currently 3oz weight in front wheels, 2oz in rear Relocated ESC to battery tray to run 4WS LCC Lower Links Losi Low Profile Carbon Fiber Front / Rear Servo Mounts LCC Drag Links Front / Rear |
Sponsored Links | |
10-02-2016, 08:08 PM | #2 |
Pebble Pounder Join Date: Mar 2016 Location: Harrisburg/York
Posts: 128
| Re: Our LNC 2.0 and LCC...
So on to my new toy, the LCC. I picked up the roller off a private sale on eBay. Barely had to clean it up, was barely ran. Currently; HobbyWing Quicrun 17.5T/1900KV Brushless Sensored with 16T Pinion. HobbyWing 10BL60 Sensored ESC Hot Racing Aluminum Motor Mount Losi Low Profile Carbon Fiber Servo Mount Spektrum SRS4210 Receiver JX PDI-6225MG High Torqure Servo Losi Aluminum Adjustable Rear Link Mount Axle Grease Access Holes drilled with Set Screws Future plans are to swap this Motor/ESC to the LNC 2.0 and upgrade to a Tekin/Holmes Hobbies. |
10-02-2016, 08:12 PM | #3 |
I wanna be Dave Join Date: Nov 2014 Location: West Texas
Posts: 2,654
| Re: Our LNC 2.0 and LCC...
Your pictures are not showing up, can't wait to see what you have been up too! 149 r/c worx team driver |
10-02-2016, 09:20 PM | #4 |
I wanna be Dave Join Date: Nov 2014 Location: West Texas
Posts: 2,654
| Re: Our LNC 2.0 and LCC...
Can you please post a link or a few pictures of the greases hole mod? 149 r/c worx team driver |
10-03-2016, 05:55 PM | #5 |
Pebble Pounder Join Date: Mar 2016 Location: Harrisburg/York
Posts: 128
| Re: Our LNC 2.0 and LCC...
Here you go. You just have to drill a hole thru the axle case and fill it with a short screw or set screw. Just make sure that it's only long enough to go thru to plug the hole and not rub against anything. |
10-03-2016, 05:56 PM | #6 |
Pebble Pounder Join Date: Mar 2016 Location: Harrisburg/York
Posts: 128
| Re: Our LNC 2.0 and LCC... |
10-03-2016, 05:58 PM | #7 |
I wanna be Dave Join Date: Nov 2014 Location: West Texas
Posts: 2,654
| Re: Our LNC 2.0 and LCC...
All of them are up except for the grease mod picture. Thank you! Very nice looking rigs. 149 r/c worx team driver |
10-03-2016, 06:01 PM | #8 |
Pebble Pounder Join Date: Mar 2016 Location: Harrisburg/York
Posts: 128
| Re: Our LNC 2.0 and LCC... |
10-03-2016, 06:03 PM | #9 |
I wanna be Dave Join Date: Nov 2014 Location: West Texas
Posts: 2,654
| Re: Our LNC 2.0 and LCC...
How do you like the speed of the brushless? Is it 3 to 5 mph? 149 r/c worx team driver |
10-03-2016, 06:13 PM | #10 | |
Pebble Pounder Join Date: Mar 2016 Location: Harrisburg/York
Posts: 128
| Re: Our LNC 2.0 and LCC... Quote:
This setup is a 17.5T/1900KV Sensored...No issues so far on low speed and has more than enough top end/wheel speed. I'm using a 16T pinion. I don't plan on doing any comp's just enjoying time with the kid so it's plenty. I picked up the Motor and ESC separately and spent about $85 total. I already had the programming card from the TC3's setup. I did change the programming, put the lipo cutoff at 3.2, full punch throttle and full reverse. I plan on going to a Tekin/Holmes Hobbies but I'll let me kid get used to the 1/10 before switching the motor/esc over. | |
10-03-2016, 06:17 PM | #11 |
I wanna be Dave Join Date: Nov 2014 Location: West Texas
Posts: 2,654
| Re: Our LNC 2.0 and LCC...
Good information. I'm building jrs rig for comping but it will get wheeled for fun also 149 r/c worx team driver |
Our LNC 2.0 and LCC... - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
???lnc/lcc??? | mudd_slinger | Team Losi Comp Crawler | 4 | 10-06-2013 09:46 PM |
lnc to lcc | heminutt | Team Losi Comp Crawler | 7 | 10-03-2013 04:09 PM |
Lcc tranny in a Lnc? | Jay2380 | Team Losi Comp Crawler | 2 | 03-27-2010 09:51 AM |
LCC vs LNC | TOYUTAH | Team Losi Comp Crawler | 9 | 01-15-2010 08:04 PM |
| |