06-16-2013, 08:30 AM | #1 |
Rock Crawler Join Date: Mar 2011 Location: hampton
Posts: 984
| welder help
i got a lincoln sp135 plus. it dont feed worth a crap, i pulled the cable out of the stinger and it had a slight kink in it. is it possible to get the kink out without screwing it up worse? a new stinger assembly is 200 bucks, this is a 135 dollar pawn shop welder |
Sponsored Links | |
06-16-2013, 11:40 AM | #2 |
Pebble Pounder Join Date: Nov 2012 Location: livonia
Posts: 109
| Re: welder help
what size wire?
|
06-16-2013, 11:59 AM | #3 |
Quarry Creeper Join Date: Jan 2013 Location: Benicia/Vallejo
Posts: 490
| Re: welder help
A new tip, feed roller, and liner will make it like new. Have you tried tightening the roller? try keeping the cable as straight as possible. Post a pic of your machine with the door open
Last edited by 1tonscout; 06-16-2013 at 02:08 PM. |
06-16-2013, 02:18 PM | #4 |
Rock Crawler Join Date: Mar 2011 Location: hampton
Posts: 984
| Re: welder help
.035 wire. there looks like a piece of wire broke off in the kink where can i get a liner from? all i can find is the whole assembly |
06-16-2013, 02:49 PM | #5 |
Quarry Creeper Join Date: Jan 2013 Location: Benicia/Vallejo
Posts: 490
| Re: welder help
Here are lincolns part numbers for the liners for your machine: Liner .023" - .030" part# M16291-2 Part Discontinued – USE KP1937-2 Liner .030" - .035" part# M16291-6 Part Discontinued – USE KP1937-3 Liner .035" - .045" part# M16291-1 Part Discontinued – USE KP1937-1 For small stuff like rc cars I would suggest going with the first one for .023"-.030" new part# KP1937-2 Ebay listing $9.95 + $5.95 shipping Lincoln MIG Welding Gun Liner KP1937 3 Magnum 100 L | eBay You're welcome |
06-16-2013, 02:58 PM | #6 |
Quarry Creeper Join Date: Jan 2013 Location: Benicia/Vallejo
Posts: 490
| Re: welder help
I would suggest an .030" tip, .030" wire and gas shield
|
06-16-2013, 03:18 PM | #7 |
Rock Crawler Join Date: Mar 2011 Location: hampton
Posts: 984
| Re: welder help
Thanks man. Didnt think about ebay |
06-16-2013, 07:25 PM | #8 |
Newbie Join Date: Feb 2010 Location: Chattanooga
Posts: 48
| Re: welder help
The sp135 is actually best run with a .023 wire and 75/25 (argon & CO2) mix. The larger wire causes the machine to reach its duty cycle faster. Higher the wire the higher the amperage causing the machine to run hot. The gun is more than likely made by tweco. A good liner from a welding supply is about $25 and don't over tighten the feed roller tensioner. The rollers are also marked and make sure those are correct for your wire size.
|
06-19-2013, 09:20 PM | #9 |
Rock Crawler Join Date: Mar 2011 Location: hampton
Posts: 984
| Re: welder help
got my liner today welder runs much better now.running flux core wire. i dont have a bottle or regulator for gas |
06-19-2013, 10:56 PM | #10 |
I wanna be Dave Join Date: Jun 2008 Location: Sin City
Posts: 3,628
| Re: welder help
get a bottle and reg for the gas upgrade and you will feel like your using a new machine all over again.
|
06-20-2013, 05:43 AM | #11 |
Rock Crawler Join Date: Mar 2011 Location: hampton
Posts: 984
| Re: welder help
what makes gas better than flux core? i have about 2 hours experience running a wire welder
|
06-20-2013, 06:09 AM | #12 |
Rock Crawler Join Date: Jun 2009 Location: summertown
Posts: 512
| |
welder help - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Welder ? | scoggdog13 | Tools, and Procedures | 8 | 03-27-2013 11:56 AM |
New T.I.G. welder | southcrawler | Scale Accessories | 7 | 09-12-2012 08:47 AM |
welder? | theloudone | Tools, and Procedures | 4 | 09-11-2012 09:54 PM |
Welder help | Double J | Tools, and Procedures | 19 | 12-17-2006 12:11 AM |
welder | wheeler | General Crawlers | 8 | 05-23-2004 10:06 PM |
| |