Official Custom ESC wiring thread.

[Chris_The_Battery_Man]

So there seems to have been a lot of interest. My other thread is kind of a mess, so this one is the official thread with prices. I offer to you, custom soldering/wiring jobs to your electronics to clean em up, and shrink the size down as much as possible. Been doing this for several years on the side, and figured I would offer it to the public.


Non-locals, You will be required to send me any electronics that you want worked over, with any wire length requests that are different than I offer.


Added 6-5:

One thing that I offer, that I haven't advertised is that I can offer the whole package ready to go with new electronics if my supplier has them in stock. BEC's seem to always be out of stock, but I can do FXR's, Micro Sidewinders, Micro pro's, Sidewinders, and BRXL's all new, put together with a BEC and programmed too if you like.

Prices include shipping and materials unless otherwise specified. All jobs will receive all new plugs and wire unless otherwise specified. Electronics done in truck are limited to locals only. Sorry. All left over components are included when truck/electronics are returned.

Smashed ESC is simply a tidied up ESC with the case still on.
Super Smashed is case removed from ESC, and soldered together as tiny as possible.


I can do other odd ball jobs too like repairs and what not. So feel free to PM me for more details and questions. Below are some links to a couple recent build threads, and the original thread I posted with some pics as well.

Dual FXR super smash:
Tekin FXR Shrink Thread - RCCrawler.com Bulletin Board

Dual mamba micro pro super smash full on job:
Spiffy XR10 Electronics shrinkage - RCCrawler.com Bulletin Board

Original Thread:
Custom Soldering/wiring - RCCrawler.com Bulletin Board





Info can now be found in the link below. Please email me via the contact us tab for more info, or if you have special requests. New prices also


CreationFab - Custom Soldering Soldering by Chris

Here are some pics from customers and myself of my work



FXR Shrink:


rbgerrish wire job:



House:



XR10 with mamba micro pro's




TheSCorpionKing



eisman's Mamba Micro Pro's and CC BEC:

[GTCharles]

I smoked my handwound motor recently in my ax10 comp crawler, that I've had for a couple years now, because I submurged it in water and had Chris take a look at it for me. He took it apart, found my armature was toast and I had him replace it. I got it back quicker then I expected and it was way cheaper then buying a new motor. I think it works better now then it did new, or maybe I've just been driving better. Either way, thanks Chris I'll definatly be talking to you if/when I finally go to an moa to get a full on job done.

[scuzzy51]

i had chris work my motors over for me! what can i say! good work chris! i noticed a huge difference! so did my truck! broke a 3rd gear pin and a cvd pin in less then 5 min after putting the motors back in! way more power! THANKS CHRIS!

[GTCharles]

I finally got an MOA and had chris do up all of my wiring. It has a single esc, punk dig, CCBEC, rx, servo and both motors all done in the truck for perfect wire length. It looks super clean and compact. Thanks a lot Chris

[DRCrawlGood]

Can you give any average turn around times for your services?

[Chris_The_Battery_Man]

Usually about a day or 2 once I have received the ESC's.

[articzap]

Super interested, but not for a few weeks. Want to get other things sorted out first.

[TSK]

Got my micro sidewinders back and am absolutely stoked. I knew they were tiny as individual units, but as a dual esc setup, being smaller than an rx is pretty dope.



Comparison to a cc BEC



Where'd my dual esc's go?



Dere dey iz!

[Chris_The_Battery_Man]

Thanks for all the support guys. Below is a link to my site. It is still in the works as of this post, but this is where you will be ordering from soon. Much easier than having to PM me. Feel free to use the contact us tab, to send me an email of you have any questions.

CreationFab - CreationFab.com Custom Soldering

[House]

I just received my FXR's from the BattMan and must say that his work is
second to none. I have done my fair share of soldering over the years but
it would take me a week straight and ten burnt fingers before I could
duplicate his work. Thanks for the great job. I also got a few of his handy
Receiver Bypass Adapters and Servo Plugs while I was at it. Nice products!

[meffie]

Just got to give a big shout out to Chris. Not only did he help me with some electrical problems, he rebuilt 4 motors for me to perfection. You can't go wrong putting your trust in Chris!

Top Notch all the way

[rocksrock]

I had Chris work on my fxr's and WOW he does some nice work. My 2 fxr's are the size of one. Well worth the money spent. thanks Chris for the good work and fast turn around time.

[new2it]

Just took my new Berg build out for a spin today - had a great first run. The wiring job you put together for me (FXR, Punk dig, CC BEC) not only looks amazing but runs amazing. Thanks Chris!

[Gso125]

Chris you did an awesome job on my dual fxr/ccbec set up. I consider myself very good with a solder gun but your work blew me away. Perfect job I recommend Chris to everyone. Thanks so much Gerry

[RPMJ]

Thanks Chris for soldering my Mamba Micros. Great job and great price.

[Chris_The_Battery_Man]

Thanks for the feedback fellas! Things are getting much busier for me thanks to your word of mouth. Keep telling your friends

[FRENCHBLUE72]

I talked to house if you would like to do some super custom work p.m. me your number..

[Highlucks]

Just been checking out some of your work bud. Very nice I must say, if only you were a little closer.

[ax10]

I've got an ax 10 with gc3 chassis. If i send esc, bec, and servo, can you solder the electronics together without the chassis? Esc is mounted on upper front links. Bec is zip tied to esc.. I would also want the bec wired directly to servo. I also want one of your reciever bypass plugs. My soldering skills are not so good. I'm looking for a nice tidy install on this new chassis. I also would want excess wire shortened.

[bob1961]

Originally Posted by Chris_The_Battery_Man

Thanks for all the support guys. Below is a link to my site. It is still in the works as of this post, but this is where you will be ordering from soon. Much easier than having to PM me. Feel free to use the contact us tab, to send me an email of you have any questions.

CreationFab - CreationFab.com Custom Soldering

so your still running cheapbatterypacks.com as well too.......bob

....