rocpede
RCC Addict
cool transfer case and are u using pinions for the gears.
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
84 Chevy Mud Bogger
- Thread starter thor04
- Start date
benoj
I wanna be Dave
great looking chevy! nice work on all the drivetrain. when you have the body done you should get some scale offroad k-30 emblems
Thanks got it all mounted up. and yup there the 5 mm 12 tooth which the bearing i used worked perfect for the shaft too. I'm gonna make a new case for it. The outer plasic i use it kinda weak but i got the general idea on how to do it now and works perfect.
slowstang88
Rock Stacker
are your transfer case shafts suspended on bearings? ive been looking for a 1/10 scale alternative like what you built.
Yes they have bearing on both ends of shafts. Well got it all mounted up after shortening the front drive shaft 1/4 inch (not easy) ended up a little bit of a angle and i put two holes in the side of the case when drilling the to bracket so i got to reskin it or go overtop and make it stonger maybe keep it a little back on both sides and give it some detail and straighten it out
peyton.
Quarry Creeper
your build looks pretty good!!!!
what kind of tranny is that?
(sorry if this was already asked)"thumbsup"
what kind of tranny is that?
(sorry if this was already asked)"thumbsup"
pantablo
I wanna be Dave
nice fab work-body, chassis, transfer case(!?).
may I suggest reduced and narrowed 2.2 mud slingers as an option?
Imex swamp dawgs:
full size 2.2
reduced to 1.5 (for a laugh, on right in picture)
may I suggest reduced and narrowed 2.2 mud slingers as an option?
Imex swamp dawgs:
full size 2.2
reduced to 1.5 (for a laugh, on right in picture)
The Tranny is out of a cordless drill. I tore apart, rebuilt and returned about 5 of them to find one that had metal gears in it and the right motor size and the funny thing is the cheapest one had them metal gears in it.
For the tire i thought about that but i'm not the best tire gluer , but i'm really liking those trail busters from rc4w but who knows right now i think the tires are gonna be last at the rate this built is going need to find a good motor/esc combo think of going with the new traxxas brushless system in ther 1/18 revo/slash units and there water proof.
For the tire i thought about that but i'm not the best tire gluer , but i'm really liking those trail busters from rc4w but who knows right now i think the tires are gonna be last at the rate this built is going need to find a good motor/esc combo think of going with the new traxxas brushless system in ther 1/18 revo/slash units and there water proof.
damn..did you make that straight frame..what kind of axles are those??Think you better put a lift on that thing! :lol::lol:
axles are HL i think.
Well its been a busy summer havent got a whole lot done other than blowing up my tranny so it back to the drawing board on that one but i did make myself a sled deck now if i had just bought myself two sleds and not one and i could find another one i would be laughing.
4mulaSvaliant
Pebble Pounder
Lovin' your build man! Got anymore done? I too will soon be uisng a motor and trans from a drill, and was wondering what I was going to do for a transfer case other than drop 80.00 for one. Sweet ideas I may have to borrow that one!
