Re: Choosing a motor and ESC for your Wraith - Gearing Added! Gearing : 8T pinion = 30.4:1, 9T pinion = 27.0: 1, 10T pinion = 24.3:1, 11T pinion = 22.1:1, 12T pinion = 20.3:1, 13T pinion = 18.7:1, 14T pinion = 17.4:1, 15T pinion = 16.2:1, 16T pinion = 15.2:1, 17T pinion = 14.3:1, 18T pinion = 13.5:1, 19T pinon = 12.8:1, 20T pinion = 12.2:1 found this on rc4wd site. i had been running a 55t with 14t pinion. i was happy with it. wanted more wheelspeed. though. i have 13 and 14tooth pinions will these be ok or am i gonna get heat issues? |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Hardly I'm planning on run a custom chassis about 10 pounds. I want it to be kinda a desert / mud racer so I'm going to need speed. My trans is a rc4wd axial 2speed. I was thinking of using a tekin 13.5 brushless but the mud wouldn't be good for it. So what brushed motor and esc you recommend. Also what gearing to use. |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Quote:
|
Re: Choosing a motor and ESC for your Wraith - Gearing Added! I'm not real sure of how to water proof a motor that's why I was thinking of using a brushed motor. I'm not looking for super fast speed just something around 30-35 MPH. |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Quote:
|
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Harley I think I've read this thread a million times, but never noticed this... From the first page "Best Choice: Holmes 16t Crawlmaster (5 slot motor which is similar to a 27t traditional 3 slot motor)" Isn't the 16T CrawlMaster more similar to a 35T TorqueMaster? |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Quote:
|
Re: Choosing a motor and ESC for your Wraith - Gearing Added! What pitch are the stock gears? |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! stock gears are 48 pitch |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Thanks |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! I am running Stock gears right now, along with the Novak Timbuk 2 and Balsistic Brushless 13.5 motor powered by 2s 5000 lipo. i please don't say get another motor...well not yet anyway. What gears should i use get get more speed out of it?? |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Quote:
|
Re: Choosing a motor and ESC for your Wraith - Gearing Added! ok.. i am going to be building a wraith kit and i am debating to get the 55t HD or the 35t HD from Tekin but my real question is what gearing should i go wit ? i will be crawlin and bashin basically 50/50 |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Quote:
|
Re: Choosing a motor and ESC for your Wraith - Gearing Added! @ Harley... Right now I'm running the stock motor 20T and stock ESC and started smoking as I was climbing up a dirt hill. I need something with more power but not slow like a turtle. Any suggestions on what I need to get. |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Thanks for this thread, Harley, it has helped a ton! |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Hallo Harley, I would like to kindly ask you: - is there any 32p set up which allows mounting the stock Transmission Cover gear - I understand some spurs might be too large to fit inside the cover... - and If there is, considering I am currently running a ratio between 6,2 to 5,4 (48p, 87/14 .. 87/16) will be there the chance to reproduce the same ratio with 32p which fits inside the cover? Many thanks for your kind reply |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! Quote:
|
Thanks a lot again Harley!! Sent from my iPhone using Tapatalk |
Re: Choosing a motor and ESC for your Wraith - Gearing Added! wanted first a tekin combo with a tekin rs and a speed passion 7.5T brushless motor,but enede up with this combo: Flux Vapor Pro Waterproof Speed Control - 106767 at HPI Europe and Flux Vektor 4000kv Brushless Motor - 106768 at HPI Europe did i go wrong or i ended up good?is the combo that comes from factory on the savage xs flux gearing will be 56/14 32 pitch with duratrax evader spur and RR pinion |
All times are GMT -6. The time now is 10:54 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com