|
| LinkBack | Thread Tools | Display Modes |
10-21-2020, 08:59 PM | #1 |
Newbie Join Date: Jun 2018 Location: NorCal
Posts: 25
| Spectrum Hobbywing Xerun problems
I have 5 crawlers with Holmes Hobbies motors and Hobbywing 1080 controllers. All have Spectrum SR515 or SR215 receivers. Everything works fine off my Spectrum DX5C transmitter. I built a new car using a Hobbywing Xerun system, 3652 brushless motor, XR8SCT controller, Spectrum SR215 receiver, DX5C trans. The Tx and Rx paired up fine. When I try to calibrate the throttle, neutral, forward, beeps but reverse does not. Turning on the system, if you touch the throttle, it goes to 100% and stays there. Hitting reverse stops it. The steering works fine. I switched receivers to the SR515 with the exact same results. The calibration does not work for throttle. Wide open at the touch of throttle. These are receivers that came off good working cars. I switched transmitters to a FlySKy GT3B, and FS receiver. First try everything works with the Hobbywing Xerun system, throttle and steering. Is there a inherent problem with the DX5C and HW Xerun system? Or does anyone know what I am doing wrong? I was reading about using a BEC, does anyone think this will cure the issue? Or switch to another brand? Last edited by davis53; 10-21-2020 at 10:51 PM. |
Sponsored Links | |
10-22-2020, 02:19 AM | #2 |
Newbie Join Date: May 2020 Location: Hampton
Posts: 27
| Re: Spectrum Hobbywing Xerun problems
Make sure your throttle end points are set to 100 or higher for throttle and brake, and you may try reversing your throttle channel. Had to do the same with my xr10 1s and my DX5PRO
|
10-22-2020, 01:21 PM | #3 |
Newbie Join Date: Jun 2018 Location: NorCal
Posts: 25
| Re: Spectrum Hobbywing Xerun problems
Thanks for your reply, end points are at 100%. I reversed motor and it made no difference.
|
10-22-2020, 10:46 PM | #4 |
I wanna be Dave Join Date: Feb 2017 Location: My mothers basement
Posts: 2,128
| Re: Spectrum Hobbywing Xerun problems
Dont you set neutral last? Sound like your setting reverse to neutral. Edit: never mind I guess on these you set neutral first __________________________ Handy gearing spreadsheet Last edited by Voodoobrew; 10-22-2020 at 11:04 PM. |
10-22-2020, 10:46 PM | #5 |
Rock Crawler Join Date: Mar 2016 Location: Zagreb, Croatia
Posts: 747
| Re: Spectrum Hobbywing Xerun problems
Not the motor, reverse the throttle channel on your radio!
|
10-23-2020, 04:35 AM | #6 |
Newbie Join Date: Jun 2018 Location: NorCal
Posts: 25
| Re: Spectrum Hobbywing Xerun problems
According to the instructions, neutral, full throttle, and full brake. In that order. But it won't accept the full brake endpoint on the ESC. The end point is set on the Tx. I reversed the motor direction with the Tx, and then with the motor programmer. No difference with either. I think it is a problem with the Spectrum, because everything works with the FlySky. |
10-23-2020, 08:05 AM | #7 |
Gold Star Baby! Join Date: Dec 2017 Location: Las Vegas
Posts: 2,554
| Re: Spectrum Hobbywing Xerun problems
Is your throttle trim set to 0 on the remote?
|
10-23-2020, 12:26 PM | #8 |
Newbie Join Date: Jun 2018 Location: NorCal
Posts: 25
| Re: Spectrum Hobbywing Xerun problems |
10-24-2020, 12:41 AM | #9 |
I wanna be Dave Join Date: Feb 2017 Location: My mothers basement
Posts: 2,128
| Re: Spectrum Hobbywing Xerun problems
I never have to reverse my throttle ch on my spektrums to calibrate.
|
10-24-2020, 10:06 AM | #10 |
Newbie Join Date: Jun 2018 Location: NorCal
Posts: 25
| Re: Spectrum Hobbywing Xerun problems
I reset the DX5C Tx and the problem of full throttle still exists. My bench test unit FlySKy GT3s works fine on this Hobbywing controller and motor. I am going to buy a new Tx/Rx system for this Hobbywing setup. Anyone have any recommendation for a new brand of transmitter?
|
10-24-2020, 01:01 PM | #11 |
I wanna be Dave Join Date: Feb 2017 Location: My mothers basement
Posts: 2,128
| Re: Spectrum Hobbywing Xerun problems
I only use spektrum, i have 3 tx's, 7rx's, 5 hobbywing esc's, an no problems. __________________________ Handy gearing spreadsheet |
10-24-2020, 08:52 PM | #12 | |
Newbie Join Date: Jun 2018 Location: NorCal
Posts: 25
| Re: Spectrum Hobbywing Xerun problems Quote:
Thanks VooDoo | |
10-25-2020, 02:09 AM | #13 |
RCC Addict Join Date: Feb 2016 Location: Santa Maria, CA
Posts: 1,751
| Re: Spectrum Hobbywing Xerun problems
For some reason, neither my DX4S nor DX5C would communicate with my Futaba A700 servo. No matter what I did, it would only turn maybe 2/3 of the way. My cheap Radiolink has no issues at all getting along with the Futaba. I've read of a few manufacturer's saying that their products won't work with Spektrum radios with no real explantion as to why, but in my case (and it sounds like yours too) switching to a different radio solved the problem. If you need channel mixing, you might want to give Futaba a look. If you don't need channel mixing, Radiolink 6ch tx's, or a Flysky GT5 might be a good choice for less scratch. |
10-25-2020, 11:24 AM | #14 |
Newbie Join Date: Jun 2018 Location: NorCal
Posts: 25
| Re: Spectrum Hobbywing Xerun problems
I have driven hundreds of miles to attend a crawl, to switch on my crawler, and have a radio glitch. I have sat on a tailgate, for hours, trying to fix the problem having people walk by to help, saying "I have the same radio at home that does the same thing." Friends are crawling and I am attempting to fix radios. I just ordered a different brand radio for all of my crawlers. Thanks for all the input everyone.
|
Spectrum Hobbywing Xerun problems - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Hobbywing Xerun AXE | Jboucher | Electronics | 565 | 06-27-2023 05:45 AM |
Hobbywing Xerun SCT | norcallump | Electronics | 4 | 09-22-2015 11:17 AM |
Hobbywing xerun 3656 3400kv | Gvm23 | Electronics | 26 | 01-30-2014 01:23 PM |
Hobbywing xerun SCT pro | Cmarcan167 | Electronics | 3 | 01-18-2014 11:11 AM |
Thread Tools | |
Display Modes | |
| |