|
| LinkBack | Thread Tools | Display Modes |
03-20-2009, 03:39 PM | #21 |
RCC Addict Join Date: Apr 2006 Location: On Da' Shelf
Posts: 1,253
|
Nice work on the steering mod. Definately need to make it out to the GTG! Going to have some kewl 1.9's out there! |
Sponsored Links | |
03-23-2009, 01:08 PM | #22 |
I wanna be Dave Join Date: Jun 2005 Location: On the G-Train!!!!!
Posts: 6,081
|
Joe seemed like it worked well yesterday. Too much fun! Here's on I managed to get if it. |
03-23-2009, 07:24 PM | #23 | ||
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
| Quote:
Quote:
Shoots.. | ||
03-23-2009, 07:41 PM | #24 |
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
| Rear Axle Brace v1
After going through her at Saturday afternoon for Sunday's GTG, I notaced that the Losi stainless steel rear axle got bent durring her maiden run. (I just joined the Losi Stainless Steel bent acxle club.. And THATS NOT GOOD..) So I had to design and make a rear axle brace in hopes that this would be the last axle to get bent. After spending the night in the shop and pissing off my neighbors, the Rear Axle Brace v1 was born. A bit over kill but with all the tumbling during yesterdays GTG the brace held up and keeped the axles from beding. I'm thinking of putting the brace on a diet for v2. Sorry for the bad close ups.:-( Shoots.. |
03-23-2009, 07:45 PM | #25 |
RCC Addict Join Date: Apr 2006 Location: On Da' Shelf
Posts: 1,253
|
That brace was beefy!!! Truck looked pretty good on the rocks. I'm sure you will have it dialed in no time. |
03-23-2009, 08:01 PM | #26 |
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
| |
03-24-2009, 12:40 AM | #27 |
Quarry Creeper Join Date: Jun 2008 Location: Honolulu
Posts: 421
|
That brace looks tough and thanks again for the shafts got them on order.
|
03-24-2009, 09:18 PM | #28 |
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
| |
03-30-2009, 12:21 PM | #29 |
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
|
Last minute mod before yesterdays comp by lowering belly clearance to ~2.125" using 3racing's RC18T shocks. She did OK durring yesterdays comp so its a keeper for now. Need to work on my neglected 2.2 rig. Shoots.. |
03-30-2009, 12:26 PM | #30 |
Rock Crawler Join Date: Dec 2005 Location: Hawaii
Posts: 888
|
Great job yesterday Joe I'm the opposite of you, just can't figure out these 1.9s.
|
03-30-2009, 12:30 PM | #31 |
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
| |
03-30-2009, 02:26 PM | #32 |
I wanna be Dave Join Date: Jun 2005 Location: On the G-Train!!!!!
Posts: 6,081
|
Great job yesterday.
|
03-30-2009, 03:35 PM | #33 |
RCC Addict Join Date: Apr 2006 Location: On Da' Shelf
Posts: 1,253
|
New shock setup looks good Joe! I bet no leaks either Sounds like the 3Racing 18T shocks worked out for ya. So how did you do yesterday? Last edited by Xtant3150c; 03-30-2009 at 09:59 PM. |
03-30-2009, 10:00 PM | #34 |
RCC Addict Join Date: Apr 2006 Location: On Da' Shelf
Posts: 1,253
|
Just saw the results from yesterday. Nice Job on the 2nd place Finish Joe |
04-05-2009, 12:12 AM | #35 | ||
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
| Thanks Sir.. Was good day with the HRCC gang.. Quote:
Quote:
Shoots.. gang | ||
04-07-2009, 09:19 PM | #36 |
Rock Crawler Join Date: Apr 2006 Location: Thorp WA, more sheep than men...
Posts: 543
|
Does that steering mod only work w/ the full size servo? Can you give me a little clearer close up of that steering setup? Killer Rig man!
|
04-07-2009, 10:04 PM | #37 | |
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
| Quote:
Also see SicksAreR's thread.. Thats where I got the idea.. He's my hero.. My KK mrc Shoots.. | |
04-15-2009, 10:15 PM | #38 |
Rock Stacker Join Date: Mar 2009 Location: cali
Posts: 51
|
love the body!
|
04-17-2009, 01:18 PM | #39 |
Quarry Creeper Join Date: Mar 2006 Location: Mililani
Posts: 229
| |
| |