Go Back   RCCrawler Forums > Vendors > MOD19RC
Loading

Notices

Thread: SMT10 DIY Backfire Header Set + Assembly Instructions

Reply
 
LinkBack Thread Tools Display Modes
Old 05-16-2020, 10:09 AM   #1
Let me 3D Print that...
 
RexRacer19's Avatar
 
Join Date: Jun 2007
Location: Concord
Posts: 303
Default SMT10 DIY Backfire Header Set + Assembly Instructions

Now available for the Axial Racing SMT10 is the Mod19RC DIY Backfire Header set. Combine this detailed, 3D printed header set with the MyTrickRC SQ-1 light controller (purchased separately) to get realistic backfire effects while driving your SMT10. Don't want the backfire effect? The headers can be used without the LEDs installed for those just wanting a highly detailed header set. Painting and assembly required. Follow the link below to the Mod19RC Shapeways store to purchase your DIY Backfire Header set today!

https://www.shapeways.com/product/Q9...e-header-set-1

A link to the MyTrickRC light controller is on the Shapeways product page for the header set.






Assembly Guide:

You will receive the 3D printed parts from Shapeways in their raw, white form. You will need to separate and trim the sprues from the pieces.






Next, paint the headers and mufflers. They can be any color you choose, but silver does have better light reflecting abilities for the LED lights. Get the dual LED lights purchased from MyTrickRC out as well.




Install the LED light starting with the lens in the end of the header. Make sure to seat the base of the lens all the way into the recess in the end of the header. This will make sure that the muffler fits all the way on. Carefully route the wire up the slot, making sure to press it all the way in. Use a dull tool for this and be careful not to damage the wires.




Next, add a few dabs of glue in a few areas to keep the wires in place. You can use epoxy, rubber cement, hot glue, etc.




Repeat the previous steps for the other header.




Slip the mufflers on carefully to check the fit. They should fit all the way up as shown below. You may want to wait to glue them on until you have the headers mounted on your chassis to get the angle to your liking.




Finally, mount the headers to your chassis, route the wires, mount the light controller, and connect all wiring as instructed in the SQ-1 instruction manual.



Enjoy the backfire effects!!!
RexRacer19 is offline   Reply With Quote
Sponsored Links
Old 06-29-2020, 06:13 AM   #2
Moderator
 
JatoTheRipper's Avatar
 
Join Date: Sep 2008
Location: PA
Posts: 13,323
Default Re: SMT10 DIY Backfire Header Set + Assembly Instructions

That's really cool.
JatoTheRipper is online now   Reply With Quote
Reply



SMT10 DIY Backfire Header Set + Assembly Instructions - Similar Threads
Thread Thread Starter Forum Replies Last Post
Backfire Exhaust! heyok Vendors Electronics 5 04-19-2016 11:09 AM
4 Link Set Up Instructions or Pic Details BMFOTP Newbie General 3 03-13-2009 12:23 PM
TLT CVD Assembly Instructions Rockpiledriver RCP Crawlers 30 06-11-2007 02:15 AM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 04:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com