|
| LinkBack | Thread Tools | Display Modes |
02-06-2014, 10:23 AM | #1 |
Newbie Join Date: Jan 2014 Location: CR
Posts: 49
| How would you apply these colors?
Just picked up a Proline Cherokee body for my current project. Its my first time painting a body and read that you should apply the darkest colors first. However, the 2 colors I'll be using are pearl white and silver. I'll be painting the fender trim/bumpers/lower body panels silver witht he rest of the jeep being painterd the pearl white. Does it matter which color goes down first?
|
Sponsored Links | |
02-06-2014, 06:42 PM | #2 |
I wanna be Dave Join Date: May 2008 Location: Baltimore
Posts: 4,442
| Re: How would you apply these colors?
You have to mask off the area that you don't want a certain color to be in for the first coat. For example, if you decided to lay down the silver first, which would be a good idea since the white would go over it in the second coat and help the color to 'pop', You need to mask off any area that you don't want the silver to show on.
|
02-06-2014, 08:43 PM | #3 |
RCC Addict Join Date: Sep 2007 Location: Hallsville, Tx
Posts: 1,820
| Re: How would you apply these colors?
You will need to buy a can of solid white to back the pearl white also. The pearl is not I solid color I believe.
|
02-06-2014, 09:17 PM | #4 |
Newbie Join Date: Jan 2014 Location: CR
Posts: 49
| Re: How would you apply these colors?
Thanks for the replies, I had figured on the masking part but was unsure which should be applied first, silver it is. I also have a spare can of Pactra white I could use after the other 2. Last question, any idea on how to simulate tinted windows? |
02-07-2014, 12:12 AM | #5 |
Fifth dimension Join Date: Oct 2012 Location: Quakertown
Posts: 2,066
| Re: How would you apply these colors?
Quick heads up. In my experience, pearl white and silver ( in my fascolor world) look too similar. I'd highly recommend backing your silver in black and pearl in white. If you need an example, pm me and I can show you a 66 ford I did with a pearl top half with some silver accents and you'll see what I mean bud. Good luck!!
|
02-07-2014, 05:21 AM | #6 |
Newbie Join Date: Jan 2014 Location: CR
Posts: 49
| Re: How would you apply these colors?
Thanks for the ehads up, sent you a PM. Im using Tamiya paints if it matters.
|
02-07-2014, 07:08 AM | #7 |
Fifth dimension Join Date: Oct 2012 Location: Quakertown
Posts: 2,066
| Re: How would you apply these colors?
I only have faskolor experience. Those rattle can colors may be very different. I didn't take tons of pics of the job but I sent you one. IMO it's tough to see how nice of a silver pin I put on that truck due to the way the pearl turned out. Just use caution bud, you'll be fine. I also test fire my colors on overhead projector sheets to see how they look next to each other. Super cheap and a great way to her a feel for what your planning
|
02-07-2014, 07:25 AM | #8 |
RCC Addict Join Date: Sep 2007 Location: Hallsville, Tx
Posts: 1,820
| Re: How would you apply these colors?
Tamiya ps12 silver is different tone than the pearl white and it is solid rnough to jot have to back it with black. I would not recommend using the Pactra paint with Tamiya, i cant remember which way it goes but it will have a chemical reaction and lift off the body. Spray the Tamiya Silver, then spray the Tamiya Pearl White, back it all with Tamiya White. Then what I would dobis back it all with the Tamiya silver to give it a good solid backing which will help protect the colors when tinting the windows. Tamiya makes a Smoke which you can use for tint, just make sure you spray it very lightly and watch for any bleed through into the lighter colors. I always like to back all my work with Tamiya Black so it is all one uniform color and it is a good protector them you can spray the tint and you wont see the over spray. One thing to keep in mind is when ypu want to spray a body 2 colors you need to be prepaired to buy atleast 3-4 differnt colors to finish it.
|
02-07-2014, 08:06 AM | #9 |
I wanna be Dave Join Date: Aug 2006 Location: under a rock and a hard place
Posts: 5,443
| Re: How would you apply these colors?
Like stated above, be really careful with the spray tint, it likes to bleed thru. If it were me I would go down to the local automotive tint center and ask for a few scraps and apply those instead. The amount you need will be far less than what the shop has laying on the floor after a job. Heck, bring your toy down and they may offer to tint it for just cuz it is cool and unusual. Ask them for a small sticker to support them.... |
02-07-2014, 03:04 PM | #10 | ||
Newbie Join Date: Jan 2014 Location: CR
Posts: 49
| Re: How would you apply these colors? Quote:
Quote:
| ||
How would you apply these colors? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
wisdom only, the rest need not apply | Duxx | Axial Wraith | 11 | 08-27-2012 02:31 PM |
Need your ideas apply with in....... | hende | Non Crawler RC's | 2 | 09-11-2010 06:39 PM |
Best way to apply weights to Vanquish SSW rims? | mdowney | Tires and Wheels | 7 | 09-06-2010 09:49 AM |
under 21 need nort apply... EeeeePeeee | toyofast | Chit Chat | 19 | 08-11-2007 09:24 AM |
| |