Re: What RC parts have you 3D Printed???? |
Re: What RC parts have you 3D Printed???? Here is a couple from my SCX Chevy build....from a junk cheapo printer. All ABS. T-case that fits stock SCX skid. Sits into the diamond patterning on the bottom to keep it as low as possible. http://www.rczoony.com/drzoo2/web/SC...5002186480.jpg Chevy LS I found the Block, Intake, Headers, Heads and Valve covers on Thingiverse. I designed the front accessories and redesigned the block for the application. Also, the inner fenders are printed. http://www.rczoony.com/drzoo2/web/SC...3068067250.jpg http://www.rczoony.com/drzoo2/web/SC...5039973290.jpg Transmission relocation mount, hard to see behind LS http://www.rczoony.com/drzoo2/web/SC...6891265724.jpg Master cylinder and Washer tank.. http://www.rczoony.com/drzoo2/web/SC...7313615440.jpg Interior, dash is styrene. http://www.rczoony.com/drzoo2/web/SC...5810502460.jpg Wheel hubs to tuck the tire inside the fender for Class 0. They held up really well. http://www.rczoony.com/drzoo2/web/SC...7863505831.jpg Intake, Airbox, Valance, Fusebox, Battery, Firewall. Everything in this pic. http://www.rczoony.com/drzoo2/web/SC...6797087235.jpg |
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? I'm starting a new engine for a Sand Scorcher based Bug. http://www.rccrawler.com/forum/membe...4547-66724.jpg |
Re: What RC parts have you 3D Printed???? Quote:
Platform Jack. |
Re: What RC parts have you 3D Printed???? Nice job, sla/dlp? Scene looks like my garage at one. Had parts of my Bus motor everywhere. Sent from my SM-N950U using Tapatalk |
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? RC boat trailer... https://scontent-yyz1-1.xx.fbcdn.net...77&oe=5CC574AB I have a couple small runabouts but they can hold a pretty good load... https://scontent-yyz1-1.xx.fbcdn.net...3f&oe=5CBBE937 Not bad for PLA leaf springs. :mrgreen: https://scontent-yyz1-1.xx.fbcdn.net...dc&oe=5CB4CA4A |
Re: What RC parts have you 3D Printed???? I designed & printed some parts for my WLToys 10428B "Clone Hammers". First was a new body mount that allowed the whole body to pivot forward instead of requiring 8 screws to get into it. This was done specifically so I could relocate the battery on my next print. I don't have a picture of it, but there's a correpsonding piece that mounted to the body/cage for another pair of magnets to attach, and the body pivots at the front bumper mount. https://farm5.staticflickr.com/4788/...c12767a5_c.jpg The reason for the hinged body was because I designed & printed a new bulkhead that holds the battery, plus it replaced the crap sliding rack steering system with proper bell cranks, and eliminated the laydown shocks for normal stand-up shocks using SCX10 shock hoops. https://farm1.staticflickr.com/794/3...fa7f9d45_c.jpg https://farm1.staticflickr.com/807/4...50946c09_c.jpg https://farm1.staticflickr.com/796/4...bd8b0cc7_c.jpg https://farm1.staticflickr.com/818/4...cf89affd_c.jpg <iframe width="640" height="360" src="https://www.youtube.com/embed/oNOxIg8QwJM" frameborder="0" allow="accelerometer; autoplay; encrypted-media; gyroscope; picture-in-picture" allowfullscreen></iframe> The overall capability of the vehicle is MUCH improved with these changes. |
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? Quote:
Yeah, that's me. |
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? Sway bar and brake light mount for the Ascender that I designed. https://i.imgur.com/TkaMZLLl.jpg?1 https://i.imgur.com/sD07A0Tl.jpg?1 https://i.imgur.com/S6pWTWVl.jpg?1 Its available on Thingiverse https://www.thingiverse.com/thing:3365848 I just made a little insert that fits inside of the stock SCX10.2 battery tray and allows the battery to be laid down instead of on its side. the stock battery box needs to be cut down, and the servo needs to be scooted up against the shock tower. https://i.imgur.com/YBPBmhkl.jpg https://i.imgur.com/Ks7Fu2rl.jpg https://i.imgur.com/J41DVrQl.jpg Made some license plate frames as well https://i.imgur.com/wjIgcEhl.jpg?1 https://i.imgur.com/9FFE4pEl.jpg?1 a few items I found on Thingiverse, Engine for the Sand Scorcher https://www.thingiverse.com/make:501818 https://i.imgur.com/KA8uaNAl.jpg I though I might use this on a build but it needs to be paired down and the exhaust needs to be changed to the trumpet pointing up style inner fenders for the SCX10.2 https://www.thingiverse.com/thing:3343085 https://i.imgur.com/d1JnRrwl.jpg these were so small though I'm not even sure what body they would work for, they dont stick out far enough to even get close to the body. Venture battery relocation mount https://www.thingiverse.com/thing:2942916 https://i.imgur.com/XmmnJjnl.jpg?1 https://i.imgur.com/m8DRcLRl.jpg?1 I don't even have the truck yet but I'm printing parts for it, lol I found some cool sanding blocks and scaled them to a few different sizes https://www.thingiverse.com/thing:2404850 https://i.imgur.com/TRz3ww7l.jpg TRX4 low cg battery mount (the wide mount they posted is broken, prints in 2 peices instead of 1) https://www.thingiverse.com/thing:2823853 https://i.imgur.com/pzORwAEl.jpg?1 I might make my own version as I need a cutout up front for my battery wires. I had BowHouse's 1st gen low cg battery mount and this one puts the battery ever so slightly lower by like 4-6 mm |
Re: What RC parts have you 3D Printed???? 2 Attachment(s) I've surprisingly not printed much for my rigs. I tend to work in styrene and metal faster than modelling complex objects anyway. We print some little doodads like screw trays, motor endbell covers, and road cones for sale. I mostly print for prototyping and shop tooling purposes. |
Re: What RC parts have you 3D Printed???? @HumboldtEF Ugh, those are great. Makes me want to get into 3d printing so bad. |
Re: What RC parts have you 3D Printed???? Quote:
I dont think you'll regret it so long as you have the space for one and the time to devote to learning the software. One more that I forgot SCX10.2 chassis https://www.thingiverse.com/thing:2854422 I printed this to mock up a build I have in the works using a Scorcher body. I had to scale it down to 83.3% to get it the stock length, even then many of the holes and spacing is off so I cant recommend using this for much else than mock ups. https://i.imgur.com/ad5k5pCl.jpg Quote:
|
Re: What RC parts have you 3D Printed???? Quote:
I have been using these... Sandpaper Holders https://scontent-yyz1-1.xx.fbcdn.net...86&oe=5CFB4859 https://scontent-yyz1-1.xx.fbcdn.net...be&oe=5CC866E3 ...but the paper jamb is a bit of a PITA sometimes. |
Re: What RC parts have you 3D Printed???? I don't know if anybody else uses the AOKoda 150W LiPo discharger/Balancer but I highly recommend it. You can get a nifty case for it that bundles all the wires and has a slide-open compartment to store the bulbs. Link to it on Thingiverse https://scontent-yyz1-1.xx.fbcdn.net...28&oe=5D009CC9 https://scontent-yyz1-1.xx.fbcdn.net...a7&oe=5CBCBD46 |
All times are GMT -6. The time now is 05:21 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com