Re: What RC parts have you 3D Printed???? wow, blast from the past product there. I've had some originals for nearly 10 years that didn't have the higher load capability. We used to mod them with bigger shunt resistors for balancing large ebike batteries. Cool little balancer/ dischargers. |
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? Storage charge really helps vs storing at 4.2v or 3v. 3.6ish volts is the happy place for a cell to be. |
Re: What RC parts have you 3D Printed???? Quote:
What printer are you using? Your stuff looks great. Quote:
|
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? Quote:
No problem, I've already seen how good the Venture does with little to no mods, I'm looking forward to a nice lightweight rig! My printer is the Prusa I3 MK3, its met and exceeded my expectations. I have no regrets with the purchase! |
Re: What RC parts have you 3D Printed???? I made up some spring perches for Wraith or Bomber shocks, theres a hole to run a zip tie though so these dont get lost. https://i.imgur.com/Qe8Bxj6l.jpg If people are interested in this I can put it up on Thingiverse, just let me know. |
Re: What RC parts have you 3D Printed???? Well before I even ran the truck I sat down and designed a flush cover for the Redcat Gen 8 rear bumper, it replaces the original hitch. I'm not anti cat, just dont want anything extra sticking out "thumbsup" Available on thingiverse for download https://www.thingiverse.com/thing:3416351 https://i.imgur.com/cbubc35l.jpg https://i.imgur.com/W2SuFiyl.jpg |
Re: What RC parts have you 3D Printed???? Got a new 3d printer (Monoprice voxel) and kind of went nuts over the last few days printing all kinds of stuff off of thingiverse. Some pull tabs for the body clips, a few Mamba-x ESC mounts for my Trx-4's, a couple of rear bumpers for my scx10 (the bar style bumper was very weak and shattered in my hands ... Not sure how to strengthen the prints up). https://uploads.tapatalk-cdn.com/201...db6c9fc131.jpghttps://uploads.tapatalk-cdn.com/201...3517b40219.jpghttps://uploads.tapatalk-cdn.com/201...79e6744c3e.jpghttps://uploads.tapatalk-cdn.com/201...12a2c470f8.jpg |
Re: What RC parts have you 3D Printed???? Quote:
I'm not familiar with the Voxel. What's the print volume? Why is the bumper printed at an angle like that? |
Re: What RC parts have you 3D Printed???? Quote:
From what I understand, the Voxel is a rebranded flashforge adventurer 3. I've had this printing 12 hours a day [emoji23][emoji23] That bumper needed to be printed on an angle because it was too long for the print bed. The strange looking supports are unique to the MP Flashprint software and it took significantly less time and wasted less PLA vs standard, vertical supports. My only issue is that the print was too brittle - much weaker than I've seen regular PLA print, so maybe it's a cheap brand of PLA+. |
Re: What RC parts have you 3D Printed???? Quote:
I assumed it was oriented that way to fit within the build volume, but wanted to make sure. Can you share that software? I'd like to check it out. For bumpers I'd suggest PETG at a minimum of that printer can do it. PLA isn't good at withstanding impacts. |
Re: What RC parts have you 3D Printed???? Quote:
If PETG is safe like PLA, then I may give that a try. I don't have room vents where I keep this printer, so my material choices are limited. |
Re: What RC parts have you 3D Printed???? Quote:
Thanks. I'll check it out. ABS emits an odor not PETG. I print almost exclusively on PETG and I don't take any special precautions. |
Re: What RC parts have you 3D Printed???? Here is the last RC parts I printed on my Ender 3. SCX10.2 inner fenders off Thingiverse. https://farm8.staticflickr.com/7800/...bd871806_b.jpgUntitled by JASON MCKIMMEY, on Flickr https://farm8.staticflickr.com/7857/...e910b815_b.jpgUntitled by JASON MCKIMMEY, on Flickr |
Re: What RC parts have you 3D Printed???? Those turned out nice. What model Ender is that; and do you like the Crealuty Ender? I have a Makergear M2 and nozzles are $10 and a replacement board is $185. I have nozzles for the MK8 hotend, and for $10 bought a few. Also two of that style hotends. Much cheaper for hotends also, M2 $100. I want a second printer, but not sure which one for under $500. Sent from my SM-N950U using Tapatalk |
Re: What RC parts have you 3D Printed???? Quote:
|
Re: What RC parts have you 3D Printed???? My first PETG print, new skid for my B1B bomber. Original test print in PLA at 30% infill didn't last very long, so this is PETG @ 0.1mm and 100% infill. If this doesn't work I'll have to either have it machined (maybe delrin?), pay Shapeways ~$65 to print it, or just give up and stick with the original skid from DMG... https://uploads.tapatalk-cdn.com/201...dc6f138408.jpg https://uploads.tapatalk-cdn.com/201...749e65d96b.jpg Sent from my SM-G930V using Tapatalk |
Re: What RC parts have you 3D Printed???? https://uploads.tapatalk-cdn.com/201...58afadd83b.jpg Did a couple low CG Battery mounts for the tax-4. Plus am printing up a Jeep body for my buddy and a second for me. Sent from my iPhone using Tapatalk |
Re: What RC parts have you 3D Printed???? I made up a rear crossmember for the Venture as I wont be using the stock battery tray/brace https://i.imgur.com/9Eehlm6l.jpg https://i.imgur.com/kgFsSQXl.jpg I'm really pleased with how this set of sliders came out for my Bug build https://i.imgur.com/EOmwEpEl.jpg https://i.imgur.com/BepCamol.jpg https://i.imgur.com/9DPGKIZl.jpg https://i.imgur.com/ACBGbGFl.jpg there's a ton more pictures of all of the other bits I've printed for the Bug in my build thread but I dont want to flood this thread http://www.rccrawler.com/forum/1-9-s...her-build.html |
All times are GMT -6. The time now is 04:25 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com