2 Attachment(s) Been getting her ready for axialfest. I lengthened the chassis by about 3/4 of an inch, went with a SS bulletproof trans, switched to an rx8 and 4000kv pro4, new wheels and all new bearings. The wheelbase is just about 13 3/4 Attachment 241817Attachment 241819 Chris M |
1 Attachment(s) Switched to Boss Claws for Axialfest Terra X.. The rig took a beating and worked perfectly!! Attachment 244297 Chris M |
Re: Terra-Wraith now with MIP mod It looks like you don't like those OMF's with Pitbulls on them. I'll do you a favor and take them :) |
Quote:
Chris M |
Re: Terra-Wraith now with MIP mod 1 Attachment(s) I got tired of the plastic gear cases deflecting under load and I had to replace the wasted r&p so in goes more aluminum. |
1 Attachment(s) Getting closer.. My goal is to have the most expensive wrexo out there.. lol Attachment 247630 http://img.tapatalk.com/d/13/07/24/zyzeqena.jpg |
Re: Terra-Wraith now with MIP mod That is one wicked looking rig. I just went and looked at my wraith and exo. And if I didn't race my exo I would probably be in there tearing the wife's wraith apart. And then sleeping on the couch. Again. Nice job. |
Re: Terra-Wraith now with MIP mod Damn. That is really nice. Wish MIP made shafts for the Exo. I would get a set. Can't wait to see more progress. |
Re: Terra-Wraith now with MIP mod Did you run MIP's in the rear too...or just the front? |
Re: Terra-Wraith now with MIP mod Quote:
It has MIP's front, rear and middle. |
Re: Terra-Wraith now with MIP mod Maybe I missed it, but what did you have to do to make the MIP stub axles fit the Exo knuckles? I assume your using Slash 4wd stub axles, correct? Looks like you've got it so bulletproofed all you'll break are diff carrier and pinion bearings. |
Quote:
|
1 Attachment(s) My old front brace wouldn't work due to the new front bulkhead holes being a little different so I had to improvise. Attachment 247838 |
1 Attachment(s) I ran into a problem while disassembling the rear. The screw pin head broke off in the mip hub and it won't come out with a punch. Looks like I may have to take angle grinder to it and replace em with new ones. Attachment 247840 Never mind, I was able to drill it a little and punch it out. The only casualty was the screw pin. http://img.tapatalk.com/d/13/07/26/terapugu.jpg |
Re: Terra-Wraith now with MIP mod Its lookin good big Chris, I think you have perfected the EXO into the ultimate G-ride... Whens the rear steer mod coming out? ****Axial, Plz take note, You NEED to Hire this guy***** |
Re: Terra-Wraith now with MIP mod Quote:
I have contemplated rear steer and dig. The only way I would do rear steer is if I added a 4 link solid rear then this rig would be just like every other wrexo out there and I like being a little different :mrgreen: Dig would be a good mod but would add more moving parts to fail. She's no comp rig and reverses are free so Ill probably just keep it as is. |
Re: Terra-Wraith now with MIP mod Nice build so far, it looks like it would be fun to drive. You can use a soldering iron to heat up those small screws and pins to help the loctite let loose so you can get them out without breaking allen wrenches inside them. |
Re: Terra-Wraith now with MIP mod Quote:
The allen tip didn't break, it was the screw pin it's self that broke just past the threads. I suspect it was already cracked from the torque load since it snapped with very little effort. Good tip, using the soldering iron though. |
1 Attachment(s) I got the rear back together. Attachment 247896 |
1 Attachment(s) And ready for the topper. I didn't mean to get my fugly toes in the pic :ror: Attachment 247906 |
All times are GMT -6. The time now is 10:28 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com