| |
08-29-2015, 08:27 PM
| #1 |
| Quarry Creeper Join Date: Dec 2010 Location: Jacksonville
Posts: 428
|  Shift Servo
Anyone have the dimensions of whats needed for the shift servo.. the China hammers one is not going to work with the new rx/radio i have  (they use a 6 wire setup.)ebay link to a servo that will work on it.. would be greatly appreciated..  |
|  |
| Sponsored Links | |
| | |
|
08-30-2015, 10:45 AM
| #2 |
| Quarry Creeper Join Date: Aug 2014 Location: Orange County
Posts: 372
| Re: Shift Servo
I use the Hitec HS-225BB and I have had my TH for about a year and I have not had any problems. If a gear was to strip then I could just buy the metal gear set and then mine would have metal gears and bearings. http://www.ebay.com/itm/Hitec-Hs-225...item51c8f602ba but there is also a metal gear version that is exactly the same just has metal gears and bushings instead of plastic gears and bearing. http://www.ebay.com/itm/Hitec-HS-225...item2ee4e34668 Sent from my iPad using Tapatalk |
|
| |
|
08-31-2015, 06:25 AM
| #3 |
| Quarry Creeper Join Date: Dec 2010 Location: Jacksonville
Posts: 428
| Re: Shift Servo
i did the Axail servo plate mod. elevated it a tad and now i can put regular size servos on it.
|
|
| |
|
09-12-2015, 10:40 AM
| #4 | |
| Quarry Creeper Join Date: Jun 2013 Location: Australia
Posts: 242
| Re: Shift Servo Quote:
Pics?? And explanation please  Sent from my iPad using Tapatalk | |
|
| |
|
09-19-2015, 07:06 AM
| #5 |
| Quarry Creeper Join Date: Jun 2013 Location: Australia
Posts: 242
| Re: Shift Servo
Can anyone help me with pics / explanation of this axial servo plate mod please?? Sent from my iPad using Tapatalk |
|
| |
|
09-21-2015, 09:38 AM
| #6 |
| Quarry Creeper Join Date: Jun 2013 Location: Australia
Posts: 242
| Re: Shift Servo
Guess not?? Sent from my iPad using Tapatalk |
|
| |
|
09-21-2015, 09:34 PM
| #7 |
| Rock Crawler  Join Date: Jul 2005 Location: Playing with toys with my son's
Posts: 616
| Re: Shift Servo
I would run a HS 5245MG, in fact I have been for 2 years now with no servo saver. Just set the end points properly.
|
|
| |
 |
Shift Servo - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Shift servo? | Minirider82 | Vaterra Ascender | 9 | 02-21-2015 11:44 AM |
| Trying to set up a Shift servo. Might have a bad servo? | m1009cucv | Electronics | 2 | 02-11-2015 07:12 AM |
| best shift servo | ax10newguy | Vaterra Twin Hammers | 4 | 07-24-2013 02:49 PM |
| Shift servo? | 09 Screw | Electronics | 5 | 03-01-2011 07:12 PM |
| shift servo | 4-linkedWK | Electronics | 3 | 04-12-2008 09:06 PM |
| |
Linear Mode
