Planning MY FIRST

[gunder463]

So I want to start getting together parts for a FOFF car, i see theres lots of different set ups out there but what dose everyone think is the best for FOFF..? As for budget i want to keep this car under 1000$ it will be my last winter build before i start the busy season for my work. and i wont be able to get into the rc's as much.

been doing some looking and i think im going to go with this chassis FOFF Whiplash 13.5" - Billet Works Designs

[evan03]

when i look at that all i see is a crawler. both front and rear shocks are layed down alot.

i think for the same money you could get a wraith skid and frame and have shock mounts better suited for high speed.

i personaly would run 2100-2650 8th scale power. but there are lotsofother lower voltage 10th scale motors and esc's that will work.

if you dont like the wraith looks you can always hack up its frame and mount whatever body you wanted on it.

150 buys alot. wraith skid is 7 bucks and new frame kits are about 80. ax10 may even be a better frame with shock mounts more vertical. you could build links to make the 13.5" mark. id then run a hot raceing scx10 tranny with exstended outputs and tmax drive shafts cut to lenght. wouldnt mess with shocks till the build was almost done and the axles of choice where mounted. revo gtr shocks would be considerd

good lucks

[evan03]

hr extended output tranny
Hot Racing Axial SCX-10 Scale Truck RC Car upgrades and Hop-ups

regular output
Hot Racing Axial SCX-10 Scale Truck RC Car upgrades and Hop-ups

these trannys can be found on ebay.

rx8 paired with a 2650 kv motor would be awesome

[gunder463]

ooo thanks for all tht info i suppose ill pick up a scx chassis then because i like the look of all the builds using those, and im experienced with the link making process so thats nuthin new, i guess ill go to the hobby shop and start buying parts and as for power plant i want to run my tekin rx8 witha 2650kv motor, i wanna get one of those bomb proof trannys they use in the crawlers but i cant find one and there out of stock.

if anyone has any other suggjestions just shout it out im open to anything this is my first build of this sort,

alright sweet, should be a fun build cant wait to start ordering parts.

alright ill have to look into that, i think im going to use ar60 axles i like the wide stance they give,

[evan03]

2650 kV will need a tranny lift to clear. DMG might make a tranny spacer to raise it up so big motors clear the skid plate

[M1tch]

I run an 1/8 motor in my foff. Its a 1965kv motor. I don't use a transmission because of the lower rpm. I use 2 1/8th transmission mounts instead and run 44T spur and 20T pinion. Made an adaptor up and used a tmaxx forward only shaft which has flats on each output. Mod 1 gears don't care about sand at all.

[gunder463]

Originally Posted by M1tch

I run an 1/8 motor in my foff. Its a 1965kv motor. I don't use a transmission because of the lower rpm. I use 2 1/8th transmission mounts instead and run 44T spur and 20T pinion. Made an adaptor up and used a tmaxx forward only shaft which has flats on each output. Mod 1 gears don't care about sand at all.

now that is sompthing awsome could you share a pic with me? i have a tmaxx tranny some where around here i could get the gears out of,

[M1tch]

If you look down through this page of the build, you can see i changed from a 1/8 buggy/truggy style motor mount to the Tekno RC mount .

Version 2.

[evan03]

Here's my 2100 kV motor on 6s 150 amp ESC.

[gunder463]

i have really been slacking, just ordered the chassis tonight and am building the trans, i have some axles i want to use but there set up for 4ws so ill have to lock out the rear and im going to use 3 link not 4 link. will post pics later.

[gunder463]

would these axles be any good for a foff?

[stelerzman]

Are they Integy? I had there ax10 alum. axle housings on "Speed Demon" and didn'thave a single issue. Jm2cents.

[Lentsnh2012]

Only if you wear those Nikes while sporting the axles.

[gunder463]

Originally Posted by stelerzman

Are they Integy? I had there ax10 alum. axle housings on "Speed Demon" and didn'thave a single issue. Jm2cents.

they are! thanks for that input now when i get my chassis i can mount em up and hopefully mount up the drive line, i still have to go to the hobby shop and get paddles for it, i know they carry just about all of them i really like the panther paddles for a sc but i wish they were as wide as sand paws

[gunder463]

Originally Posted by Lentsnh2012

Only if you wear those Nikes while sporting the axles.

i just like the color green haha

[stelerzman]

UGC-FF4 Foff, SPEED DEMON

Here is my Speed Demon thread. Look through it and you might find some ideas.
There are plenty of pics and some video links.

[gunder463]

i went out and grabbed panther paddles for it and put them on my sct beadlocks,

[gunder463]

Finally got my chassis, time to put it together,

[gunder463]

heres what i got started,

[gunder463]

more progress,