RCCrawler Forums

JohnRobHolmes · 09-01-2008, 01:01 PM

You will be perfectly fine. I have run the 7t on a sidewinder with 3s lipo with no problems.

Your batteries may get warm, and if you try and stall the motor out they can get over drawn. Just depends on how much power you try to use.

Siggy · 09-02-2008, 07:44 AM

Will there be a chance to purchase a couple of spare brushes and replacement 7T comms?

I am really liking much the powerful torque presence yet smooth driving at crawling speed fed by an 8-cell and 3S lipo.

Thanks for an awsome product and the top-rate service!

JohnRobHolmes · 09-02-2008, 08:08 AM

I am still waiting to hear about brushes. If the original factory won't do it I will have to source elsewhere. Replacement armatures are not available at this time, but luckily these guys wear pretty slow in a crawler!

Siggy · 09-02-2008, 08:18 AM

Appreciate much the effort in looking for alternative sources. Although your absolutely right, these brushes or the comm don't wear-out quickly at crawling speed.

Cheers!

CowboysYJLT1 · 09-03-2008, 12:46 PM

I am running a Tekin FXR ESC, Castle Creations bec unit to power 2 servos with a RC4WD R2 transmission with driveline disconnect for front dig. I was wondering if set up will hold up to the 7T puller and do you have any of the motors and the 11.1V batteries in stock?

ctrwannabe · 09-05-2008, 11:10 AM

so these are still avalable? I would like to stay brushed but have awesome power and low speed controle as well. My problem is i still use NiMh so ill be compleatly new to lipo batts and chargers, also my esc is a rooster crawler (brushed) would it be able to handle a 3c lipo or maybe i need a 2c i realy dont know, this is going into my 2.2 comp bannana with ax10 drivetrain, thanks for any info.

ElkySS · 09-06-2008, 07:45 AM

Any word on shipping yet? I ordered one from your website and it still says 3rd of sept.i might give you a call later and see if I can catch up to you.

cuzican · 09-18-2008, 03:05 PM

Is there any chance one of the 7t cobalts will work with my Rooster Crawler ESC??

Deezul · 09-26-2008, 12:11 PM

it should

JohnRobHolmes · 09-26-2008, 12:20 PM

Quote:

Originally Posted by cuzican

Is there any chance one of the 7t cobalts will work with my Rooster Crawler ESC??

Yep, works just fine.

mikedoug · 10-03-2008, 10:34 AM

So has it been determined that none of these motors run well on 6 cell 1500's? I just spent some $ having packs made, would hate to have to tsell them to go back to sub C's just to run a 10t. Will the 10T run on the 2/3A 1500s? Basically, I have acces to one of these motors, but am not sure it will work great for me on this battery setup.

JohnRobHolmes · 10-03-2008, 10:38 AM

The 10t would be fine on 6cell 2/3a. You will have some limit to the power, but judge whether your driving is too much for the cells by the tempurature. If you batteries stay cool, you are just fine.

mikedoug · 10-03-2008, 10:46 AM

Thanks for the reply! I just don't have the wheelspeed I am looking for with the novak 55turn. Here in AZ I feel like I get into a lot of spots where I could use some power to be popping over stuff. I think this will be just what I am looking for.

Deezul · 10-06-2008, 08:05 PM

Quote:

Originally Posted by mikedoug

Thanks for the reply! I just don't have the wheelspeed I am looking for with the novak 55turn. Here in AZ I feel like I get into a lot of spots where I could use some power to be popping over stuff. I think this will be just what I am looking for.

I was in the same situation as you. Def get the puller. I have the 7t and run 8cell 2/3A 1600's.....seems to work fine

tuner · 10-07-2008, 12:38 AM

When will the TorqueMaster Minis be back in stock?

Jeepial · 10-07-2008, 08:26 PM

Hey John can I trade in my Crawlmaster brushless for a 7 turn?....LOL...I can do without brushless motors..

JohnRobHolmes · 10-07-2008, 08:42 PM

Quote:

Originally Posted by gs tunner

When will the TorqueMaster Minis be back in stock?

End of the week is the plan.

Quote:

Originally Posted by caesarleigh

Hello John, will there be anymore production runs of the 10T cobalt puller?
Or should I grab a 7T before they are all gone?
TIA

The 10t will be next year. In the mean time 7t is all I have.

killjoyken · 11-06-2008, 07:30 PM

Hey John, do you think a Tekin FX-R Pro w/CCBEC would handle the 7t on 3s lipo?

I've got an extra MM, but I love the Tekin's drag brake...

JohnRobHolmes · 11-07-2008, 08:10 AM

Yeah, no problem with that combo.

billysnarf · 11-11-2008, 12:42 PM

John, I have seen much written about the cobalt 7 and 10 turn puller motors.. and i know you are sold out of the 35t handwound motos... i was wondering how the cobalt 500 compares to these other motos... im running 3 cell lipo w/tekin fxr and currently have a novak 55 turn.. i want something more than this current moto has too offer.. any advice?

09-03-2008, 12:46 PM	#385
CowboysYJLT1 Newbie Join Date: Aug 2008 Location: FT Bragg Posts: 41	I am running a Tekin FXR ESC, Castle Creations bec unit to power 2 servos with a RC4WD R2 transmission with driveline disconnect for front dig. I was wondering if set up will hold up to the 7T puller and do you have any of the motors and the 11.1V batteries in stock? Last edited by CowboysYJLT1; 09-03-2008 at 01:11 PM.

HH Cobalt Puller- Reborn page 35! - Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
R1 + Cobalt Puller	Highlucks	G-Made Crawlers	3	05-31-2010 09:38 PM

09-01-2008, 01:01 PM	#381
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	You will be perfectly fine. I have run the 7t on a sidewinder with 3s lipo with no problems. Your batteries may get warm, and if you try and stall the motor out they can get over drawn. Just depends on how much power you try to use.

09-02-2008, 07:44 AM	#382
Siggy RCC Addict Join Date: Apr 2008 Location: Singapore Posts: 1,742	Will there be a chance to purchase a couple of spare brushes and replacement 7T comms? I am really liking much the powerful torque presence yet smooth driving at crawling speed fed by an 8-cell and 3S lipo. Thanks for an awsome product and the top-rate service!

09-02-2008, 08:08 AM	#383
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	I am still waiting to hear about brushes. If the original factory won't do it I will have to source elsewhere. Replacement armatures are not available at this time, but luckily these guys wear pretty slow in a crawler!

09-02-2008, 08:18 AM	#384
Siggy RCC Addict Join Date: Apr 2008 Location: Singapore Posts: 1,742	Appreciate much the effort in looking for alternative sources. Although your absolutely right, these brushes or the comm don't wear-out quickly at crawling speed. Cheers!

09-05-2008, 11:10 AM	#386
ctrwannabe RCC Addict Join Date: Jun 2007 Location: San Antonio, Tx Posts: 1,093	so these are still avalable? I would like to stay brushed but have awesome power and low speed controle as well. My problem is i still use NiMh so ill be compleatly new to lipo batts and chargers, also my esc is a rooster crawler (brushed) would it be able to handle a 3c lipo or maybe i need a 2c i realy dont know, this is going into my 2.2 comp bannana with ax10 drivetrain, thanks for any info.

09-06-2008, 07:45 AM	#387
ElkySS Pebble Pounder Join Date: Apr 2008 Location: Tulsa Posts: 110	Any word on shipping yet? I ordered one from your website and it still says 3rd of sept.i might give you a call later and see if I can catch up to you.

09-18-2008, 03:05 PM	#388
cuzican Pebble Pounder Join Date: Jun 2008 Location: Kalispell Posts: 119	Is there any chance one of the 7t cobalts will work with my Rooster Crawler ESC??

09-26-2008, 12:11 PM	#389
Deezul RCC Addict Join Date: Feb 2006 Location: ccxc Posts: 1,176	it should

10-03-2008, 10:34 AM	#391
mikedoug Newbie Join Date: Sep 2008 Location: hot Posts: 27	So has it been determined that none of these motors run well on 6 cell 1500's? I just spent some $ having packs made, would hate to have to tsell them to go back to sub C's just to run a 10t. Will the 10T run on the 2/3A 1500s? Basically, I have acces to one of these motors, but am not sure it will work great for me on this battery setup.

10-03-2008, 10:38 AM	#392
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	The 10t would be fine on 6cell 2/3a. You will have some limit to the power, but judge whether your driving is too much for the cells by the tempurature. If you batteries stay cool, you are just fine.

Sponsored Links

10-03-2008, 10:46 AM	#393
mikedoug Newbie Join Date: Sep 2008 Location: hot Posts: 27	Thanks for the reply! I just don't have the wheelspeed I am looking for with the novak 55turn. Here in AZ I feel like I get into a lot of spots where I could use some power to be popping over stuff. I think this will be just what I am looking for.

10-07-2008, 12:38 AM	#395
tuner Rock Crawler Join Date: May 2007 Location: Salt Lake City Posts: 977	When will the TorqueMaster Minis be back in stock?

10-07-2008, 08:26 PM	#396
Jeepial I wanna be Dave Join Date: Sep 2008 Location: behind the wheel of a monster truck... Posts: 2,878	Hey John can I trade in my Crawlmaster brushless for a 7 turn?....LOL...I can do without brushless motors..

11-06-2008, 07:30 PM	#398
killjoyken Quarry Creeper Join Date: Nov 2006 Location: San Jose Posts: 353	Hey John, do you think a Tekin FX-R Pro w/CCBEC would handle the 7t on 3s lipo? I've got an extra MM, but I love the Tekin's drag brake...

11-07-2008, 08:10 AM	#399
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	Yeah, no problem with that combo.

11-11-2008, 12:42 PM	#400
billysnarf Quarry Creeper Join Date: Apr 2008 Location: dallas Posts: 271	John, I have seen much written about the cobalt 7 and 10 turn puller motors.. and i know you are sold out of the 35t handwound motos... i was wondering how the cobalt 500 compares to these other motos... im running 3 cell lipo w/tekin fxr and currently have a novak 55 turn.. i want something more than this current moto has too offer.. any advice?

RCCrawler Forums

Thread: HH Cobalt Puller- Reborn page 35!