07-13-2014, 08:26 PM | #2621 |
Pebble Pounder Join Date: Jul 2007 Location: Reedsburg
Posts: 193
| Re: Official WiRCRC Chit Chat
I want it strong though is a two speed going to handle brushless power?
|
Sponsored Links | |
07-13-2014, 08:30 PM | #2622 |
Newbie Join Date: Apr 2014 Location: Superior, WI
Posts: 22
|
I'm not exactly sure. But I do know I have a fast wraith and a slow wraith. If I had a two speed I would only need one wraith lol. Anyone else have everywhere with the wraith 2 does trannys?
|
07-13-2014, 08:40 PM | #2623 |
Pebble Pounder Join Date: Jul 2007 Location: Reedsburg
Posts: 193
| Re: Official WiRCRC Chit Chat
What did you do the trans in your wraiths and I'm way over thinking it because it's just a spur gear but I'm thinking all metal gears spur and all internal gears metal also and a set of mip drive shafts
|
07-13-2014, 08:44 PM | #2624 |
Newbie Join Date: Apr 2014 Location: Superior, WI
Posts: 22
|
I don't like all metal spurs. To loud. But I do like the metal internal gears. I just fill ERM tight with grease to keep the noise down
|
07-13-2014, 09:07 PM | #2625 |
Pebble Pounder Join Date: Jul 2007 Location: Reedsburg
Posts: 193
| Re: Official WiRCRC Chit Chat
I might just do the axial steels gears inside with 32p gears and mip drive shafts i also need to get a new trans case becaus one of my mounting screws that mounts the trans to the skid is striped out
|
07-13-2014, 09:35 PM | #2626 |
Newbie Join Date: Apr 2014 Location: Superior, WI
Posts: 22
|
There you go. I picked up a hot racing trans on eBay. That has steel gears and aluminum housing. I've been waiting for a stock one to go out to release it with. But haven't needed it yet. The MIP spine shafts will help allot. The stock ones really like to twizzler up when brushless power is applied. What motor and ESC are you going to run? |
07-14-2014, 05:12 AM | #2627 |
Pebble Pounder Join Date: Jul 2007 Location: Reedsburg
Posts: 193
| Re: Official WiRCRC Chit Chat
I plan on a mamba max pro with the tekin roc412
|
07-14-2014, 10:37 AM | #2628 |
RCC Addict Join Date: Jul 2008 Location: Fox Valley WI
Posts: 1,691
| Re: Official WiRCRC Chit Chat
I have the RC4WD 2 speed trans in 3 trucks. They have held up just fine with a 35 turn/3S combo.....big brushless power will most likely snap the input shaft. That's the word I hear on the forum anyway. They do make an HD replacement shaft but I haven't heard if it'll hold up better.
|
07-14-2014, 02:45 PM | #2629 |
Pebble Pounder Join Date: Jul 2007 Location: Reedsburg
Posts: 193
| Re: Official WiRCRC Chit Chat
I could buy a bomb proof complete trans for 200 but I'm not sure I want to spend that much to upgrade to brushless in three years lol I'm thinking about the Rc4wd trans not sure yet
|
07-14-2014, 04:56 PM | #2630 |
Newbie Join Date: Jan 2013 Location: port washington
Posts: 44
|
Sorry I been M.I.A. yall, the fam fell apart im solo now :-(
|
07-14-2014, 07:24 PM | #2631 |
Pebble Pounder Join Date: Jul 2007 Location: Reedsburg
Posts: 193
| Re: Official WiRCRC Chit Chat
welcome back and i figure out what i want to do with my wraith im going to get 32 pitch gears 56 spur and 11-14 tooth pinions and metal gears in the trans might steal the mips off my scx10 and buy the extended output shaft for the rear mip and run them on my wraith so now what to sell lol the revo or my dingo
|
07-15-2014, 12:07 PM | #2632 |
Pebble Pounder Join Date: Jun 2009 Location: prairie du sac
Posts: 108
| Re: Official WiRCRC Chit Chat |
07-16-2014, 10:31 PM | #2633 | |
Rock Stacker Join Date: May 2009 Location: Wausau
Posts: 82
| Re: Official WiRCRC Chit Chat Quote:
one thing I kept around was the scaler to force me to get out and it was head clearing/good stress reliever time. waiting for the new tranny gears to get here after blowing 2 idler gears when we met up with stolps over the 4th | |
07-19-2014, 02:14 PM | #2634 |
Pebble Pounder Join Date: Jul 2007 Location: Reedsburg
Posts: 193
| Re: Official WiRCRC Chit Chat
Wondering if putting my fxr esc in a balloon is a bad idea it will be in a wraith it won't fit in the receiver box
Last edited by 1santaever; 07-19-2014 at 02:21 PM. |
07-20-2014, 07:28 PM | #2635 |
Pebble Pounder Join Date: Jun 2009 Location: prairie du sac
Posts: 108
| Re: Official WiRCRC Chit Chat |
07-20-2014, 08:56 PM | #2636 |
RCC Addict Join Date: Jul 2008 Location: Fox Valley WI
Posts: 1,691
| Re: Official WiRCRC Chit Chat
Bring it on! |
07-20-2014, 09:10 PM | #2637 |
Pebble Pounder Join Date: Jul 2007 Location: Reedsburg
Posts: 193
| Re: Official WiRCRC Chit Chat
Come on dawg you know your Chevy can't keep up with my jeep stop lying lol
|
07-21-2014, 06:22 AM | #2638 |
Pebble Pounder Join Date: Jun 2009 Location: prairie du sac
Posts: 108
| Re: Official WiRCRC Chit Chat |
07-21-2014, 09:20 AM | #2639 |
RCC Addict Join Date: Jul 2008 Location: Fox Valley WI
Posts: 1,691
| Re: Official WiRCRC Chit Chat
I'm guessing it's gonna be an SCX-10 with a Bronco body rollin' on 2.2's?
|
07-21-2014, 09:22 AM | #2640 |
Rock Crawler Join Date: Feb 2009 Location: Wrightstown
Posts: 960
| Re: Official WiRCRC Chit Chat |
| |