03-01-2018, 07:20 PM | #1501 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Had a project come my way. Needed to replicate a bumper, but in another color. So I designed the piece in my software, then printed it. White piece is the original, black is PLA+ 3d printed plastic. The two black bumpers are the finished product. One was a test piece that came out terrible. Changed the print orientation and it came out great! This was a really nice learning experience. I haven't had the need to replicate a piece before really. The keen may observe that it's not a 100% replica. I felt a solid piece would be stronger in the material. It's actually the same weight, give or take, as the original. I also changed some of the rear facing angles for ease of printing. This took me a few hours of work. I was considering using a photo stitching program to 3d render the bumper, but I haven't gone down that rabbit hole yet. Someone wants me to design a motorcycle fender 1:1, so that'll be interesting! Photos: |
Sponsored Links | |
03-01-2018, 10:21 PM | #1502 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
I did another thing. |
03-11-2018, 09:12 PM | #1503 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
More things-- Red in the rear, white up front. |
03-12-2018, 04:08 AM | #1504 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on?? |
03-12-2018, 04:29 AM | #1505 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
C clamp mounts. The Ascender cage is a smaller diameter than Axial, so I wrapped electrical tape to thicken it up. Last edited by robertjpjr; 03-12-2018 at 04:39 AM. |
03-13-2018, 07:45 AM | #1506 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Finished Product: |
03-18-2018, 07:30 PM | #1507 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on?? |
03-25-2018, 10:23 PM | #1508 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on?? |
03-26-2018, 04:26 AM | #1509 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
Pretty cool! the turn signals arent nearly as obnoxious as some Ive seen, they seem to not enable until there a good amount of input to the servo |
03-30-2018, 10:28 PM | #1510 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on?? Made a solder 3rd hand. Found a diy instructable on the internet. I had worn my original one out. Have 5 hands instead of 2 for about $10 |
03-31-2018, 05:10 PM | #1511 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Got out today and did a break in on the TRX4 Bronco. Needed to shake these winter build blues.
|
03-31-2018, 05:31 PM | #1512 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on?? have a 10 ii coming. Getting the new Proline 46 Power Wagon Body. |
04-06-2018, 07:20 PM | #1513 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
46' Power Wagon Scx10ii Came with a ROC412, MMP , King shocks and Rc4wd wheels. Had to put pitbulls on this one. |
04-15-2018, 09:35 AM | #1514 |
Pebble Pounder Join Date: Nov 2013 Location: Bath,ME
Posts: 159
| Re: What are you working on??
Time to clean the dust and cob webs off!
|
04-20-2018, 06:25 PM | #1515 |
Pebble Pounder Join Date: May 2013 Location: Nobleboro
Posts: 158
| Re: What are you working on??
Got the 10ii done. Used magnets but they aren't strong enough to keep the lid on if it gets hit. So a little Velcro to help out will go on in the morning. |
07-21-2018, 10:48 PM | #1516 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Had a MMP ESC fail a few weeks back. Sitting on the shelf killed it I guess... Sent it to Castle, $95 dollars later I have a killer Mamba X ESC. Pulled the MMP that was in the TRX4 replaced with the X. Since the TRX4 has the largest motor it got the big ESC. Photo is crap, just a bunch of wires, but here it is nonetheless. |
08-12-2018, 02:41 PM | #1517 |
Quarry Creeper Join Date: Oct 2011 Location: Westport Island
Posts: 404
| Re: What are you working on??
Finally got around to installing a few bits I’ve had since FEBRUARY..... Installing a rear locker and under drive gears in the OG TRX and was pleasantly surprised to see the Traxxas gear set came with a plug to seal where the diff lock cable once was. Oh, and a new power plant... Sent from my iPhone using Tapatalk |
08-15-2018, 08:05 PM | #1518 |
RCC Addict Join Date: Sep 2015 Location: Southern Maine
Posts: 1,024
| Re: What are you working on??
I worked on opening the box. I’m tired... Sent from my iPhone using Tapatalk |
11-07-2018, 11:16 AM | #1519 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
Found a cool 3d print file online. Paid $6.50 for the files. The fenders turned out nice. https://pinshape.com/items/30293-3d-...ab-floor-sides The rear tray section, is pointless. (Photos in link) No way to attach it, kind of a bummer. Didn't notice it in the photo, but the rear piece is being held up by a clamp! Oh well. Fenders have nice detail, and fitment is great. Need to 3d print a changed battery tray setup, easy fix. I'm going to try and print a rear fender setup. More scale, I dislike seeing wires, and ESC. ETC. |
11-07-2018, 10:58 PM | #1520 |
Rock Crawler Join Date: Oct 2013 Location: Wiscasset, ME
Posts: 623
| Re: What are you working on??
More photos. Printed different sliders to fit the fenders. Also got the plow truck ready. |
What are you working on?? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Working out | ozyint | Chit Chat | 6 | 08-02-2011 02:34 PM |
Something new I am working on | sparky0068 | 1.9 Scale Rigs | 24 | 08-16-2008 10:14 PM |
Little Something We Was Working On | pureadrenalin | Chit Chat | 33 | 10-22-2007 11:03 AM |
Im Working On A Working Wrecker Any Ideas? | LEDDPIPE | General Scale Talk | 7 | 12-13-2006 11:53 PM |
What I've been working on...... | CSR | Tamiya Txt-1 and Juggernaut | 26 | 11-10-2005 04:54 PM |
| |