10-15-2011, 12:51 PM | #221 |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
| Paradox BTL Plate installation
I updated the badges on the bug body. Gotta represent the corp. BTL Servo Installation, just in time for the new version to come out... The tie rod link was too long (notice the bow leggedness) All I had was a file, and yes it took a long time. Installed (This picture was taken with a iphone 4s with pretty bad light. Still a pretty decent picture) |
Sponsored Links | |
10-15-2011, 07:06 PM | #222 |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
|
some crawling: I don't know how it possibly rolled off the cliff from so far away but it did... No damage woo! |
10-15-2011, 09:04 PM | #223 |
RCC Addict Join Date: Apr 2010 Location: Ringwood
Posts: 1,233
|
nice man looks good i have the version 1 BTL i bet this one is better |
10-16-2011, 12:21 PM | #224 |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
|
This spot has been the bane of my existence. I don't know what to do to the car to make it get over that overhang...Besides dig. Venom Creeper RC 'sped up failure'.mov - YouTube |
10-16-2011, 01:40 PM | #225 |
Pebble Pounder Join Date: Jun 2011 Location: Port Charlotte
Posts: 180
|
How much weight are you running in your tires?
|
10-16-2011, 02:30 PM | #226 | |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| Quote:
| |
10-16-2011, 02:48 PM | #227 |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
|
The front wheels weigh 12oz total. The rears weigh 9oz. I can't add any more weight to the front wheels, there just isn't any room unless I get new wheels. I haven't cut the star shapes into the outer foams. Maybe that could help. This is the foams i have: HB WD Rover & 5.5 Double Deuce Foam Combo Front Inners: Firm Inners Inner Front Width: 2.00 Front Outers: Soft Outers Rear Inners: Firm Inners Inner Rear Width: 2.00 Rear Outers: Medium Outers |
10-16-2011, 03:12 PM | #228 |
Pebble Pounder Join Date: Jun 2011 Location: Port Charlotte
Posts: 180
|
I agree with too stiff foams. Also your wheel base may be too short for that climb.
|
10-16-2011, 04:17 PM | #229 |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
|
I have a lot of stuttering when moving as slow as possible. I replaced the batteries in the controller and stuck the antenna out away from stuff. It seems to be getting worse, now when I go in reverse the servo tweaks out too. see video: electronics issue - YouTube |
10-16-2011, 04:25 PM | #230 |
RCC Addict Join Date: Sep 2010 Location: Malta, NY
Posts: 1,340
|
my electronics do that 2. im not spasic on what the issue is, but its either the servo no haveing a neg wire going to the RX, or it is just the radio that im using.
|
10-16-2011, 06:34 PM | #231 |
Pebble Pounder Join Date: Jun 2011 Location: Port Charlotte
Posts: 180
|
With the video being sped up I couldn't tell if it was glitching. but now that you said that it does I think along with the foams being to stiff the glitching is a big problem as it causes wheel hop.
|
10-16-2011, 07:35 PM | #232 |
RCC Addict Join Date: Apr 2010 Location: Ringwood
Posts: 1,233
|
iv got some weigths for the stock creeper rims that would add 7.5oz to ur front that go on the outside of the rim Last edited by asw27x; 10-16-2011 at 07:37 PM. |
10-16-2011, 09:52 PM | #233 | |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| Quote:
| |
10-16-2011, 09:56 PM | #234 | |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| Quote:
| |
10-17-2011, 10:43 AM | #235 |
Pebble Pounder Join Date: Nov 2010 Location: Mesa
Posts: 198
|
I had a similar problem when I put in a FXR speed control. Turned out that with the Castle Bec I just had to run the ground wire from the servo to the rx and problem solved. I dont know what your electronics are but this worked for me and a few other people I know. Strange though it would not glitch at all with 2s, only on 3s?
|
10-17-2011, 11:02 AM | #236 | |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
| Quote:
| |
10-17-2011, 11:05 AM | #237 |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
|
Well I was doing a little wire management to make sure everything was in its place on the rig and i apparently reversed the connection wire between the receiver to the esc... The receiver promptly filled my house with delicious cancer-smoke. I ordered a new receiver. I hope that it the only part that got fried! lame |
10-17-2011, 11:06 AM | #238 |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
| |
10-17-2011, 11:07 AM | #239 |
Rock Crawler Join Date: Apr 2011 Location: Sonoma County
Posts: 517
| Should I do star cuts in the outer foams? Do you do that?
|
10-17-2011, 12:02 PM | #240 |
RCC Addict Join Date: Apr 2010 Location: Ringwood
Posts: 1,233
| |
Tags |
3d print, build, creeper, step by step, venom |
| |