|
![]() |
| LinkBack | Thread Tools | Display Modes |
![]() | #1 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
I just got a venom creeper and i was putting the drive shafts together and this one little piece would not fit its product # is 8318 does any one know why that is or some info that could help. Thanks.
Last edited by scoggdog13; 03-10-2013 at 05:00 PM. |
![]() | ![]() |
Sponsored Links | |
![]() | #2 |
Pebble Pounder ![]() Join Date: Jun 2011 Location: Port Charlotte
Posts: 180
| ![]() 8318 - M2.5 X 2.5mm Set Screw |
![]() | ![]() |
![]() | #3 |
Pebble Pounder ![]() Join Date: Jun 2011 Location: Port Charlotte
Posts: 180
| ![]()
Here's a pic.
|
![]() | ![]() |
![]() | #4 |
Pebble Pounder Join Date: Jan 2012 Location: usa
Posts: 143
| ![]()
I believe if you use the upgraded parts (Pin retainers) the set screws that hold the pins in are not needed. Mine did not fit either, but I changed over to traxxas shafts.
|
![]() | ![]() |
![]() | #5 | |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| ![]() Quote:
You have to have the set screws to hold drive shafts on but on the cvd's axle shafts you dont... | |
![]() | ![]() |
![]() | #6 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
Can you turn a venom creeper into a venom safari creeper by putting a frame or chassis on it
|
![]() | ![]() |
![]() | #7 |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| ![]()
A Venom Safari is a Creeper...with frame rail kit bolted on top and a body and a dig unit.
|
![]() | ![]() |
![]() | #8 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
where would i get a frame rail kit at
|
![]() | ![]() |
![]() | #9 |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| ![]() |
![]() | ![]() |
![]() | #10 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
Does the Traxxas 2056 servo come with a servo arm or do you have to buy one?
|
![]() | ![]() |
![]() | #11 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
Does the rc4wd 35t motor come with the wires already attached
|
![]() | ![]() |
![]() | #12 | |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| ![]() Quote:
No...if it was pre-wired it would say so...or if it came with wire it would say so. It a selling point in advertising. | |
![]() | ![]() |
![]() | #13 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
what servo arm do u use on a venom creeper with a venom high torque servo
|
![]() | ![]() |
![]() | #14 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
i finally got my creeper running and i cant keep the rear diff lock locked any suggestions on what i should do
|
![]() | ![]() |
![]() | #15 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
does it have something to do with the screw on the switch
|
![]() | ![]() |
![]() | #16 |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| ![]() |
![]() | ![]() |
![]() | #17 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
I just got my creeper running tday and i was going up this obstacle i made and my right front tire got caught and i hit forwards and snapped the short axle shaft. it sucks i will prbly get one tmrw though
|
![]() | ![]() |
![]() | #18 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
i want a more scale rc and i already have the venom creeper so i think i was going to turn the venom creeper into the safari creeper but i dont know what parts to get and could you mount the shocks of the venom creeepr straight up and down by mounting them to the frame. i want the frame rails and everything because i want to put a chevy blazer body on it.
|
![]() | ![]() |
![]() | #19 |
I wanna be Dave Join Date: Jan 2006 Location: ...the burning end of the rope.
Posts: 5,013
| ![]()
Some small aluminum angle or flat bar from the local hardware store can make a cheap and very strong scale ladder frame.
|
![]() | ![]() |
![]() | #20 |
Pebble Pounder Join Date: Mar 2012 Location: Carrollton, IL
Posts: 184
| ![]()
ok and i have a venom 50t motor with a axial ae-1 esc and want it to go a little faster so i was thinking of useing a axial 20t or 27t motor would that work with that esc and all stock parts along with the stock motor pinion gear
|
![]() | ![]() |
![]() |
![]() | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Venom Creeper Safari Front Driveshaft issues | xxROELKEYxx | Venom Creeper | 24 | 02-05-2012 07:33 AM |
venom torque twist issues | gsmall | Venom Creeper | 6 | 03-19-2011 07:52 PM |
Safari creeper issues | THEDUDE79 | Venom Creeper | 0 | 03-04-2011 07:28 AM |
New Creeper build issues - Not very good QC at Venom... | rwkhaussupply | Venom Creeper | 15 | 01-19-2010 06:56 AM |
Bit confuessed about the creeper. | MATT01234 | Venom Creeper | 4 | 11-06-2009 02:08 PM |
Thread Tools | |
Display Modes | |
| |