03-31-2017, 06:22 PM | #121 | |
Rock Crawler Join Date: Nov 2014 Location: Dells
Posts: 697
| Re: Mamba Firmware V2.02 Quote:
Now if only the next FW for the micro had the upper voltage limit turned off... | |
Sponsored Links | |
03-31-2017, 06:25 PM | #122 |
Pebble Pounder Join Date: Dec 2012 Location: Delaware
Posts: 154
| Re: Mamba Firmware V2.02 Correct.. no disagreement there.. but also the drag brake strength and also torque of the motor is much less using a small can/rotor
|
03-31-2017, 06:30 PM | #123 | |
Rock Crawler Join Date: Nov 2014 Location: Dells
Posts: 697
| Re: Mamba Firmware V2.02 Quote:
I run mostly 2 pole 540 motors. My favorite is an old trinity d3.5 17.5kv.... Anything above ~60% db will hold the truck from rolling, any higher and it just endos Do you run 2s, 3s, or 4s? Drag brake and torque go up with higher voltage. | |
03-31-2017, 06:38 PM | #124 | |
Pebble Pounder Join Date: Dec 2012 Location: Delaware
Posts: 154
| Re: Mamba Firmware V2.02 Quote:
Again, were talking completely still on 50* inclines/declines And the castle crawler motor is smaller than a 540.. hopefully people have noticed that | |
04-02-2017, 07:41 PM | #125 |
Rock Crawler Join Date: Nov 2014 Location: Dells
Posts: 697
| Re: Mamba Firmware V2.02
Are the new lower KV 1406 motors 5mm shaft or 3mm? Website is down right now... |
04-02-2017, 08:25 PM | #126 |
I wanna be Dave Join Date: Jun 2016 Location: Deep in the Everglades
Posts: 5,818
| Re: Mamba Firmware V2.02
3mm Hang up and Drive |
04-06-2017, 02:45 PM | #127 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Re: Mamba Firmware V2.02 I haven't tested this newest release, it sounds like they listened to myself and others and tuned these "slate" colored motors for better startup. I would assume the rotors were modified to lower detent. Or they got the software dialed in to soften the startup. Either way, good that Castle is listening and pushing hard into crawling. Well, good for everybody except me and Tekin |
04-06-2017, 04:27 PM | #128 |
RCC Addict Join Date: Sep 2014 Location: Alberta
Posts: 1,116
| Re: Mamba Firmware V2.02
And this is why I respect JRH ^ and will continue to purchase his products.
|
04-07-2017, 10:28 PM | #129 |
Quarry Creeper Join Date: Dec 2015 Location: Sutter
Posts: 489
| Re: Mamba Firmware V2.02
Any ideas what is going on here. Monster X w/HH 3500kv Puller Pro. Holmes sensor wire. V2.02, Turnigy 3 cell 60c. GT3C with abs disabled. https://youtu.be/h1PE2kzJdyA Sent from my iPhone using Tapatalk |
04-07-2017, 10:30 PM | #130 | |
Rock Crawler Join Date: Nov 2014 Location: Dells
Posts: 697
| Re: Mamba Firmware V2.02 Quote:
| |
04-07-2017, 10:33 PM | #131 |
Quarry Creeper Join Date: Dec 2015 Location: Sutter
Posts: 489
| Re: Mamba Firmware V2.02
Double checked that before. It's wired correctly but you are right that that is how it's acting. Sent from my iPhone using Tapatalk |
04-07-2017, 10:36 PM | #132 |
Rock Crawler Join Date: Nov 2014 Location: Dells
Posts: 697
| Re: Mamba Firmware V2.02
Are any motor tabs shorted together from a bad solder job?
|
04-07-2017, 10:40 PM | #133 |
Quarry Creeper Join Date: Dec 2015 Location: Sutter
Posts: 489
| Re: Mamba Firmware V2.02 |
04-07-2017, 10:50 PM | #134 |
I wanna be Dave Join Date: Apr 2015 Location: Roseville, Ca
Posts: 2,506
| Re: Mamba Firmware V2.02
That's cogging. Check sensor wire is plugged in all the way.
|
04-09-2017, 08:53 AM | #135 | |
Moderator Join Date: Sep 2008 Location: PA
Posts: 13,935
| Re: Mamba Firmware V2.02 Quote:
| |
04-09-2017, 10:50 AM | #136 |
I wanna be Dave Join Date: Jun 2016 Location: Deep in the Everglades
Posts: 5,818
| Re: Mamba Firmware V2.02
If you have look at your throttle settings, I bumped mine back 4 and it was a nightmare, thought sensor wire, after many minutes I saw the bar on my display , I use a Futaba though Hang up and Drive |
04-09-2017, 11:53 AM | #137 | |
Quarry Creeper Join Date: Dec 2015 Location: Sutter
Posts: 489
| Re: Mamba Firmware V2.02 Quote:
Yes it is updated v2.02. I did double check that the Holmes sensor wire is plugged in fully and stopped by the lhs to pick up a castle adapter so I can try one of the many old sensor wires I have. Sent from my iPhone using Tapatalk | |
04-09-2017, 12:05 PM | #138 |
Moderator Join Date: Sep 2008 Location: PA
Posts: 13,935
| Re: Mamba Firmware V2.02 It's probably not the sensor cable, but it's worth checking.
|
04-09-2017, 01:01 PM | #139 |
Quarry Creeper Join Date: Dec 2015 Location: Sutter
Posts: 489
| Re: Mamba Firmware V2.02 |
04-09-2017, 01:22 PM | #140 |
Moderator Join Date: Sep 2008 Location: PA
Posts: 13,935
| Re: Mamba Firmware V2.02 Mine acted the same way. It was the firmware. But even the new firmware that I tried (the version before the current release) needed to be on the correct settings or it cogged. I forget what that setting was though. It might have been sensored instead of Smart Sense. I forget how Castle does their settings. I'll try to remember to looking into it when I get home.
|
Mamba Firmware V2.02 - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
castle firmware update1.46 | JesterSpec | Axial Yeti | 7 | 12-19-2014 08:33 AM |
Sidewinder Micro firmware | dextan22 | Electronics | 6 | 04-18-2013 02:00 PM |
Castle Firmware | skid plate | Electronics | 2 | 01-11-2011 10:23 AM |
Glitching with New Castle Firmware | EXW | Electronics | 16 | 01-24-2010 07:56 AM |
| |