RCCrawler Forums

Offroader5 · 02-21-2008, 12:36 PM

Quote:

Originally Posted by JohnRobHolmes

I don't know if I will offer this service anymore. I am on the verge of work overload from the soldering that I offer, so I will not offer it on any more products at this time. I may even pull soldering from all of my other products too. I would rather have better customer service than soldering service in the long run.

Would I just put a note in the comments field then in Paypal about which ends to include with the motor?

Wrecker · 02-21-2008, 12:51 PM

Thanks for the help and clarification JRH!

JohnRobHolmes · 02-21-2008, 01:45 PM

Quote:

Originally Posted by crawl rookie

So the Esc is enough for this motor, and 4-6 weeks from now?
What about the Crawlmaster and a Quark22 or will that be on/over the egde for the esc? well i'll just wait a bit till they get to you

Please report when they are in stock again?
thx again!

Mischa

The 22 amp is enough for the Revolver, but not the Crawlmaster.

I will post up when I get them back in stock.

Quote:

Originally Posted by Offroader5

Would I just put a note in the comments field then in Paypal about which ends to include with the motor?

Yes, in the commend field would be great. Or purchase a set of plugs to your liking. The Castle 4mm plugs are really nice.

Quote:

Originally Posted by wrecker

Thanks for the help and clarification JRH!

Your welcome!

solomon7 · 02-21-2008, 08:12 PM

Hey John, how are ya making that inline Dean's adapter for the CC BEC? IS that 2 females or a male and female?
Better yet , I soldered the posts of a male and female together with the red and black wires to the BEC in effect leaving a male and female end for the ESC and Bat. to plug in to. There is a bit of space between the plugs though. Is that what ya did? I don't want to plug it in until I know it's done right ya know? Any feedback or explanation of yours and mine would certainly be reassuring! Thanks yet again!

nj05nismo · 02-22-2008, 04:31 AM

i kept meaning to ask. is it possible to trim the cage at the back of the motor? im thinking of running one of these monsters in my tuber but it wont fit with that cage intact...

JohnRobHolmes · 02-22-2008, 08:11 AM

Quote:

Originally Posted by solomon7

Hey John, how are ya making that inline Dean's adapter for the CC BEC? IS that 2 females or a male and female?
Better yet , I soldered the posts of a male and female together with the red and black wires to the BEC in effect leaving a male and female end for the ESC and Bat. to plug in to. There is a bit of space between the plugs though. Is that what ya did? I don't want to plug it in until I know it's done right ya know? Any feedback or explanation of yours and mine would certainly be reassuring! Thanks yet again!

Yep, I just solder deans back to back with the power lead tapped to each side just like you did. I cover the void with electrical tape.

Quote:

Originally Posted by nj05nismo

i kept meaning to ask. is it possible to trim the cage at the back of the motor? im thinking of running one of these monsters in my tuber but it wont fit with that cage intact...

I would say no, but you could grind them just a bit. The rear cage holds the brush hood, so if you remove part of it the motor is ruined.

chivas72 · 02-22-2008, 09:05 AM

no luck on this yet ? still out of stock

do you have pics mounted on a tlt axle ?

JohnRobHolmes · 02-22-2008, 09:12 AM

Thanks for the reminder, I had a few left. I don't have any pics on a tlt axle, but depending on your rims the packs do fit.

solomon7 · 02-22-2008, 12:20 PM

Thanks for the confirmation John!~ It just looked odd, ya know?

BIGBIRD · 02-22-2008, 02:31 PM

HI JOHN, i preordered two 7t motors, but would like to add 1 more to my order. can i do this in one transaction, i dont want to pay shipping twice. and when will you be posting 10t for preorder i need one of those as well., i have been watching your web page 10 times every day this week. thanks,RICK

crawl rookie · 02-22-2008, 03:14 PM

John can u help me with some info one more time

?
please look at this link:
Genius 30 brushed-BL
thx man

And since your Pm is disabled how can i contact you for an order?
i just saw you cant awnser to Hotmail mail :(

brushlessnut · 02-23-2008, 09:54 AM

lipo temps how hot can a lipo get befor it will swell or pop Im running around 100* on a 8c 3s pack with the puller

Scattman · 02-23-2008, 12:03 PM

Hey John, quick question.

How warm should 2/3 A nimh packs be at end of charge?
I thought I heard you once say 130*. Is that correct?

Thanks

JohnRobHolmes · 02-23-2008, 12:24 PM

Quote:

Originally Posted by crawl rookie

John can u help me with some info one more time

?
please look at this link:
Genius 30 brushed-BL
thx man

And since your Pm is disabled how can i contact you for an order?
i just saw you cant awnser to Hotmail mail :(

I have never used the Genius, so I can't give proper advice. You will need to use a mail service other than hotmail, get a Gmail account or something. Hotmail thinks I am a spammer, so it won't let me send email to hotmail accounts from my website.

Quote:

Originally Posted by brushlessnut

lipo temps how hot can a lipo get befor it will swell or pop Im running around 100* on a 8c 3s pack with the puller

130F is the max operating temp of a lipo. Just because it doesn't get hot doesn't mean it isn't getting overdrawn. I already told you that you will need more battery

Quote:

Originally Posted by Scattman

Hey John, quick question.

How warm should 2/3 A nimh packs be at end of charge?
I thought I heard you once say 130*. Is that correct?

Thanks

140 to 145F is the normal peak temp of nimh.

solomon7 · 02-23-2008, 12:50 PM

Thanks for your help on the bec wiring John. Now that I have bypassed the roosterce's BEC and am running it at 6V, can I run more than 7 nimh cells o rdoes the ESC's cell limit still apply? Wanna run 8 if I can but not if it will damage anything especially my $90 ESC! Thanks bro! You are a cut above the rest

crawl rookie · 02-24-2008, 12:15 PM

Quote:

Originally Posted by JohnRobHolmes

The 22 amp is enough for the Revolver, but not the Crawlmaster.

I will post up when I get them back in stock.

Your welcome!

You've got mail

Made a Gmail account like you advised

steve01646 · 02-24-2008, 04:09 PM

Hi John was wondering when u will have more Elite 8 cell packs avail there is one showing ont he website wanted to get 2 and a Castle BEC?
Thanks Steve

T_Boy · 02-24-2008, 05:49 PM

Hey John, I am wanting to run a brushless setup in my 1.9 scale rig. I was wondering if I were to get an outrunner motor from you and run it with my mamba max with your 9cell (10.8V) battery if it would work for a good all around trail setup. Thanks for the help.

Motor: http://holmeshobbies.com/product.php...&cat=19&page=1

Battery: http://holmeshobbies.com/product.php...&cat=10&page=1

Big_Ern · 02-24-2008, 10:21 PM

Hi John,

I want to preorder a Cobalt Puller 7T. I tried to do it on your site, but living in Canada, it wouldn't let me

I sent you an email about it, but just wanted to make sure you get it. Please let me know the total cost (I emailed you my shipping address) and I will send you a manual PayPal transfer right away. Also let me know what email I should use to paypal you

I would prefer one of the cheaper USPS shipping methods.

Thanks!

Aaron

HITMAN · 02-25-2008, 10:50 AM

Hey John, i have the Hyperion EOS0606I AC/DC Charger, will the built in balancer adapter work with a thunder power 1320mah 3 cell 11.1 lipo? if not what adapter do i need to purchase to make it work. thx. joe

02-21-2008, 08:12 PM	#424
solomon7 Rock Crawler Join Date: Jul 2007 Location: Portland,OR Posts: 888	Inline adapter question Hey John, how are ya making that inline Dean's adapter for the CC BEC? IS that 2 females or a male and female? Better yet , I soldered the posts of a male and female together with the red and black wires to the BEC in effect leaving a male and female end for the ESC and Bat. to plug in to. There is a bit of space between the plugs though. Is that what ya did? I don't want to plug it in until I know it's done right ya know? Any feedback or explanation of yours and mine would certainly be reassuring! Thanks yet again!

02-22-2008, 03:14 PM	#431
crawl rookie Rock Crawler Join Date: Sep 2005 Location: IDK Posts: 852	John can u help me with some info one more time? please look at this link: Genius 30 brushed-BL thx man And since your Pm is disabled how can i contact you for an order? i just saw you cant awnser to Hotmail mail :( Last edited by crawl rookie; 02-22-2008 at 03:16 PM.

02-24-2008, 04:09 PM	#437
steve01646 Newbie Join Date: Oct 2007 Location: Council Bluffs Posts: 8	8 cell packs? Hi John was wondering when u will have more Elite 8 cell packs avail there is one showing ont he website wanted to get 2 and a Castle BEC? Thanks Steve

02-24-2008, 10:21 PM	#439
Big_Ern Rock Stacker Join Date: Dec 2007 Location: Langley BC Posts: 77	7T preorder Hi John, I want to preorder a Cobalt Puller 7T. I tried to do it on your site, but living in Canada, it wouldn't let me I sent you an email about it, but just wanted to make sure you get it. Please let me know the total cost (I emailed you my shipping address) and I will send you a manual PayPal transfer right away. Also let me know what email I should use to paypal you I would prefer one of the cheaper USPS shipping methods. Thanks! Aaron

(HH) Tech Questions and Customer support thread - Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Futaba customer support	XJkid93	Chit Chat	6	07-24-2012 06:07 PM
ZNO-RC Customer Support	ZNO-RC	Redcat Crawlers	28	03-20-2012 08:44 PM
axial customer support/service THANKS!	superflex	General Crawlers	6	01-31-2011 08:40 PM
airtronics customer support	dlamb11877sf	Electronics	0	04-13-2010 10:04 AM

02-21-2008, 12:51 PM	#422
Wrecker [HOONIGAN] Join Date: Nov 2005 Location: Grand Junction Posts: 4,269	Thanks for the help and clarification JRH!

02-22-2008, 04:31 AM	#425
nj05nismo Rock Crawler Join Date: Sep 2007 Location: University City Posts: 627	i kept meaning to ask. is it possible to trim the cage at the back of the motor? im thinking of running one of these monsters in my tuber but it wont fit with that cage intact...

02-22-2008, 09:05 AM	#427
chivas72 RCC Addict Join Date: May 2005 Location: I live Here Posts: 1,218	no luck on this yet ? still out of stock do you have pics mounted on a tlt axle ?

02-22-2008, 09:12 AM	#428
JohnRobHolmes owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down! Posts: 20,290	Thanks for the reminder, I had a few left. I don't have any pics on a tlt axle, but depending on your rims the packs do fit.

02-22-2008, 12:20 PM	#429
solomon7 Rock Crawler Join Date: Jul 2007 Location: Portland,OR Posts: 888	Thanks for the confirmation John!~ It just looked odd, ya know?

02-22-2008, 02:31 PM	#430
BIGBIRD Pebble Pounder Join Date: Jan 2008 Location: nowhere near the HAMMERS!! Posts: 165	HI JOHN, i preordered two 7t motors, but would like to add 1 more to my order. can i do this in one transaction, i dont want to pay shipping twice. and when will you be posting 10t for preorder i need one of those as well., i have been watching your web page 10 times every day this week. thanks,RICK

02-23-2008, 09:54 AM	#432
brushlessnut RCC Addict Join Date: Mar 2007 Location: des moines Posts: 1,104	lipo temps how hot can a lipo get befor it will swell or pop Im running around 100* on a 8c 3s pack with the puller

02-23-2008, 12:03 PM	#433
Scattman Official Cook of the ECC Join Date: Dec 2005 Location: Hawthorne, Florida Posts: 2,653	Hey John, quick question. How warm should 2/3 A nimh packs be at end of charge? I thought I heard you once say 130*. Is that correct? Thanks

02-23-2008, 12:50 PM	#435
solomon7 Rock Crawler Join Date: Jul 2007 Location: Portland,OR Posts: 888	Thanks for your help on the bec wiring John. Now that I have bypassed the roosterce's BEC and am running it at 6V, can I run more than 7 nimh cells o rdoes the ESC's cell limit still apply? Wanna run 8 if I can but not if it will damage anything especially my $90 ESC! Thanks bro! You are a cut above the rest

02-24-2008, 05:49 PM	#438
T_Boy Quarry Creeper Join Date: May 2005 Location: Newton Posts: 219	Hey John, I am wanting to run a brushless setup in my 1.9 scale rig. I was wondering if I were to get an outrunner motor from you and run it with my mamba max with your 9cell (10.8V) battery if it would work for a good all around trail setup. Thanks for the help. Motor: http://holmeshobbies.com/product.php...&cat=19&page=1 Battery: http://holmeshobbies.com/product.php...&cat=10&page=1

Sponsored Links

02-25-2008, 10:50 AM	#440
HITMAN Rock Crawler Join Date: Jul 2005 Location: Phoenixville Posts: 826	Hey John, i have the Hyperion EOS0606I AC/DC Charger, will the built in balancer adapter work with a thunder power 1320mah 3 cell 11.1 lipo? if not what adapter do i need to purchase to make it work. thx. joe

RCCrawler Forums

Thread: (HH) Tech Questions and Customer support thread