06-20-2008, 05:39 PM | #941 |
Rock Stacker Join Date: May 2008 Location: Rohnert park
Posts: 82
|
hello recently i bought 2 of your crawlmaster motors one 850kv crawlmaster and one 1000kv crawlmaster sport, i installed the 850kv on my ax10 rtr with a mamba max esc and a cc bec. after i installed it i tested it and it sqeals and has no power any time i put it under load it just squeals and lugs like power is on and off. i was wondering what if any advice you could give me.:-(
|
Sponsored Links | |
06-20-2008, 06:59 PM | #942 |
Quarry Creeper Join Date: Jan 2008 Location: akrowdy
Posts: 304
|
jrh looking to mount a 7t puller to an rc4wd 2 speed ... need the motor plate so i dont have to drill out the tranny could not find it on your site .... what pinion do u suggest ... 3s lipo . sidewinder . thanks
|
06-21-2008, 09:18 AM | #943 |
Quarry Creeper Join Date: Oct 2005 Location: ELLENSBURG, WA
Posts: 336
| Gell batt ?
JR .. A lil crawler OT, but I can't find an answer. I have a 12V 7 amp gel for a starter box. My auto charger has a gel, 2 amp mode. Will I kill the batt with this ? TIA
|
06-21-2008, 11:38 AM | #944 | |
Keep it real Join Date: Jun 2006 Location: Yakima,WA
Posts: 6,532
| Quote:
| |
06-21-2008, 06:55 PM | #945 |
Pebble Pounder Join Date: Nov 2007 Location: la verne
Posts: 197
|
john, somewheres i heard you had a pdf schematic for the microswitch dig setup for the berg crawlers. i figured it out(killing power to one motor) but i wanted the printout if its located here anywhere? thanx
|
06-22-2008, 09:00 AM | #946 |
Quarry Creeper Join Date: Sep 2007 Location: Near my tools
Posts: 276
|
hi john, i got hyperion eos0606i(DC only) today. i did read the manual, but not use my charger yet. there is a charge, discarge and cycle mode in nicd/nimh modes. when i use this cycle mode? use it on all batteries or just batteries that not use for long time? then, i had lipo battery 11.1v 1800mah with no balancer connector, is it save charging without balancer connector? thank's |
06-23-2008, 01:24 PM | #947 |
Pebble Pounder Join Date: Feb 2008 Location: Bala Cynwyd
Posts: 111
| Outrunner Motor Plate
John, I have a Revolver Outrunner, AX-10 (purchased from you), do I need the Axial Outrunner motor plate or will the stock one work. I checked the motor against the plate supplied with the kit and the holes line up but I don't know if there is some other reason for needing the other motor plate. Thnx Last edited by HaSharetz; 06-24-2008 at 06:36 AM. |
06-24-2008, 02:39 PM | #948 |
Tire&Foam Extraordinaire Join Date: Jun 2007 Location: C.I. Compound, Tyler, Texas
Posts: 5,601
|
JRH, when will you have more Side Winders in stock? I would like to order a Side Winder and BEC from you.
|
06-25-2008, 09:01 AM | #949 |
I wanna be Dave Join Date: May 2006 Location: HONDURAS...ROCK HEAVEN
Posts: 5,076
|
Hi Johnrob, i need a couple more castle voltage regulators i forgot to include in the order, any chance you put it the same shipment? pm the total for 2 of the voltage regulators. Thanks, Carlos |
06-25-2008, 11:48 AM | #950 |
Pebble Pounder Join Date: Apr 2008 Location: greenville
Posts: 127
| 7t puller
ive got a question? my puller just started arcing real bad at the brushes. it ran fine at the last comp then i went to turn it on to run today and it started. any idea on the cause?
|
06-26-2008, 10:03 AM | #951 | ||||||||||
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
| Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Quote:
Arcing would be caused by the timing being negative. Check the endbell and see if it is loose. You may need to retime it. | ||||||||||
06-27-2008, 07:17 AM | #952 |
I wanna be Dave Join Date: May 2006 Location: HONDURAS...ROCK HEAVEN
Posts: 5,076
| |
06-27-2008, 08:52 AM | #953 |
Newbie Join Date: Jan 2008 Location: *
Posts: 41
|
NOOB Question. I would like to upgrade my battery pack not sure which way to go? 2cell 7.4 1300mah lipo or 6/8 cell saddle packs 1500mah. Would the lipo have more punch or longer run times? Thanks for your help 65t motor sidewinder esc |
06-27-2008, 09:11 AM | #954 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
|
The lipo would have less runtime but more punch. It would keep a higher voltage under load as compared to the 6 cell pack. I would choose an 8 cell nimh over a lipo unless you have space to mount the two cell on your axle.
|
06-27-2008, 09:18 AM | #955 |
Newbie Join Date: Jan 2008 Location: *
Posts: 41
|
I was thinking about mounting to the front axle. Do you offer a higher mah in the smaller size lipo.
|
06-27-2008, 09:28 AM | #956 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
|
not at the moment. You could run two in parallel and stack them. Otherwise any more MAH means a longer cell right now. I am working on something with more mah, but it will take a while.
|
06-27-2008, 11:00 AM | #957 |
Pebble Pounder Join Date: Apr 2008 Location: greenville
Posts: 127
|
Arcing would be caused by the timing being negative. Check the endbell and see if it is loose. You may need to retime it.[/quote] how do i retime it? |
06-27-2008, 11:06 AM | #958 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
|
I will probably need to take pics if you are not familiar with the procedure. Basically the brushes need to be right between the magnets if you look down the motor.
|
06-27-2008, 11:11 AM | #959 |
Pebble Pounder Join Date: Apr 2008 Location: greenville
Posts: 127
| |
06-27-2008, 11:15 AM | #960 |
owner, Holmes Hobbies LLC Join Date: Nov 2004 Location: Volt up! Gear down!
Posts: 20,290
|
Will do, I will message you with the thread/ link when I get it done. Probably this evening, I know you want to get running as fast as possible.
|
(HH) Tech Questions and Customer support thread - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Futaba customer support | XJkid93 | Chit Chat | 6 | 07-24-2012 06:07 PM |
ZNO-RC Customer Support | ZNO-RC | Redcat Crawlers | 28 | 03-20-2012 08:44 PM |
axial customer support/service THANKS! | superflex | General Crawlers | 6 | 01-31-2011 08:40 PM |
airtronics customer support | dlamb11877sf | Electronics | 0 | 04-13-2010 10:04 AM |
| |